724656
10
Zoom out
Zoom in
Previous page
1/16
Next page
12v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: LCD699-2SC • 11/2017 • 54731
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
12v Lithium-ion Cordless Drill with Hammer Action
MODEL No.: LCD699-2SC • 11/2017 • 54731
16 17
Using the drill/driver
Trigger switch
1. Use the forward/reverse switch (6) to select the
direction of rotation (Fig E), then pull the trigger
(8) (Fig F). This trigger switch is an electronic
variable speed control which enables the user to
vary the speed continuously.
The speed varies according to how far the
trigger switch is depressed.
The further it is depressed the faster the chuck
will rotate and the lighter it is depressed, the
slower it will rotate.
2. To stop the drill/driver, release the trigger
switch (8).
Note. The variable speed control tted to this
drill/driver is NOT intended to be used for long
periods of time during the operation of the task
being performed. Use the variable speed to
start drill/driving and screwing tasks, and then
fully depress the trigger once the task has started.
CAUTION. Extended use of the variable speed under load will overload and
then permanently damage the speed control.
Drill/driver Overload
This drill/driver is tted with an overload protection. If the drill/driver is
excessively forced, or the task being performed is too great for the drill/
driver, the drill/driver will automatically go into an overload mode. When
the drill/driver goes into overload, the drill/driver will automatically and
suddenly STOP. To reset the overload, simply release the trigger. When the
trigger is pressed again, the drill/driver will restart. Resume work after the
overload has been reset, but reduce the load by using a smaller drill/driver
bit or re-sharpen the existing drill/driver bit and reduce the amount of force
placed on the drill/driver. If the drill/driver is set to High speed on the gear
selector, consider changing to low speed selection.
CAUTION. Do not continue to overload the drill/driver and constantly reset
the overload. Doing this will cause the battery cells to over heat.
Temperature cut out
If the drill/driver is constantly overloaded, or the drill/driver is used
constantly at maximum rating in high ambient conditions, the battery cells
may overheat causing the battery pack to shut down.
When this occurs you will need to allow the battery cells to cool.
NOTE: The drill/driver will not restart until the battery pack has cooled.
To reduce the temperature of the cells remove the battery pack from the
drill/driver and place the battery pack in a free air environment, out of direct
sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators or
freezers.
When the battery pack has cooled down it can again be used to operate
the drill/driver, as long as the load or the conditions causing the original
excessive temperature has been corrected.
Low voltage cut out
The battery pack used on this tool is tted with a low voltage cut out feature
within the circuitry.
The low voltage cut out feature operates when the voltage drops below a
preset value. This feature automatically stops the drill/driver from operating
(similar to that of the overload condition). When this condition occurs you
will need to either insert another battery into the drill/driver or recharge the
existing battery.
The low voltage cut out feature has been added to maximise the life of the
battery cells in the battery (9). When this occurs, recharge the battery pack
by following the battery charging section in this manual.
NOTE: Attempting to restart the tool without either recharging the battery
or installing another battery (with charge) will lead to drill/driver restarting
and then stopping again, after only a few seconds of operation.
Forward/reverse switch
NOTE: You can only change the direction of rotation of the drill/driver using
the forward/reverse switch (6) when the trigger (8) is NOT depressed.
This switch will allow you to change the direction of the motor while the
trigger switch is not depressed.
Usig the Drill / Driver Temperature Cut out
F.
E.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone LCD699-2SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone LCD699-2SC in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info