724656
8
Zoom out
Zoom in
Previous page
1/16
Next page
12v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: LCD699-2SC • 11/2017 • 54731
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
12v Lithium-ion Cordless Drill with Hammer Action
MODEL No.: LCD699-2SC • 11/2017 • 54731
12 13
Parts List Product Care
Important information – Product care
This drill/driver uses Lithium Ion Battery Cells. Care MUST be taken to ensure
both the safety and life of the pack is maintained. Ensure you have read all of
the safety notes in the previous pages before using the drill/driver.
Treat the battery pack with care and within the guidelines of this manual.
If the pack does become immersed in water or any uids, or is subject to
a severe drop or it does not operate within the guidelines of this manual,
immediately STOP using the battery pack and have it checked.
During operation avoid overloading the drill/driver. If the drill/driver is
overloaded it will automatically STOP. Overloading may occur for a number
of reasons including when the drill/driver is pushed too hard or when using
a drill/driver bit or attachment greater than what is specied. If you do
overload the drill/driver during operation refer to the “Overload” section in
this manual.
NOTE: When the battery of the drill/driver is at the lower end of the charge,
the drill/driver is more susceptible to the overload condition.
Running the drill/driver at close to maximum load, or continual resetting
of the overload will cause the battery pack to overheat. When a preset cell
temperature is detected, the battery pack will automatically STOP operating
and will not restart until the battery pack has cooled to a safe level.
In this condition, DO NOT force cool the pack by placing in a freezer or
similar device. Refer to the “Overload” section in this manual.
Another feature of the drill/driver/battery pack is the low voltage cut out
feature. This feature operates when the voltage drops below a preset value.
When this occurs the tool will automatically stop operating. To correct the
situation you need to either insert another charged battery into the drill/
driver or recharge the existing battery, and then proceed with the drill/
driving application.
NOTE: Attempting to restart the tool in this condition without either
recharging the battery or installing a battery with charge will lead to drill/
driver restarting and then stopping again after only a few seconds of
operation.
These safety devices have been tted for the safety, reliability and life of the
tool.
Parts List
1. Drill/Driver chuck
2. Torque setting/ collar
3. Function selection collar
4. Two speed high /low gear selector
5. Side Belt Clip
6. Forward/Reverse & Lock
control/switch
7. Rechargeable battery display
8. Variable speed, On/O trigger switch
for drill, brake, light control,
and battery display
9. Rechargeable battery
10. 1 Hour Battery charger
11. 1 Hour LED Battery charger indicators
11a. 1 Hour battery charger
charging” indicator
11b. 1 Hour battery charger “power”
indicator, and “ready to use” indicator
12. LED work light
13. Side Belt Clip recess
14. Hammer function symbol
15. Screw function symbol
16. Drill function symbol
6
9
7
12
8
9
10
1
2 3
4
5
13
11a
11b
16 14
15
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone LCD699-2SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone LCD699-2SC in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info