724656
14
Zoom out
Zoom in
Previous page
1/16
Next page
12v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: LCD699-2SC • 11/2017 • 54731
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
12v Lithium-ion Cordless Drill with Hammer Action
MODEL No.: LCD699-2SC • 11/2017 • 54731
24 25
Warranty/Service Environmental Protection
What your 5 year warranty means
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly.
In the event of product failure within its intended use over the course of
the rst 5 years after the date of purchase, we will remedy the problem as
quickly as possible once it has been brought to our attention. In the unlikely
event of such an occurrence, or if you require any information about the
product please contact us via our after sales support services, details of
which can be found in this manual and on the product itself.
After Sales Support TEL: 1800 909 909
Service Support
If you have any issues with the operation of your product, please call us on
1800 909 909 for advice, or email us at help@powertoolsupport.com
Accessories and after Sales Parts
The following accessories are available for purchase by visiting
www.extrabattery.com.au or calling our customer service hotline on:
1800 909 909
1. 54731 - 12V Battery
(LY699-LI-12V)
2. 54731 - 12V 1 Hour
Charger (LYKC699-S)
FAQ/Troubleshooting
Do I need to charge the battery before use?
Yes, New battery packs are usually shipped in a below full charge condition and should be
fully charged before use. It takes up to 1 hour to fully charge your new battery.
Folllow the section in this manual on the details to charge the battery (9). If the battery is
placed in the charger (10) and the green charge indicator (11b) light stays on in FULL, and
the red charging indicator (11b) does not come on, then the battery (9) may already be
charged. This does NOT indicate a fault. In this case, t the battery (9) into the drill and run
for approx 3- 5 minutes. Then remove the battery (9) from the drill and place back in the
charger (10), and the red charge indicator (11a) will glow. Charge the battery (9) until the
red light turns o and the green “ready to use light (11b) remains on in full.
Follow the full section “Battery Charging “ in this manual on page 14-15.
Charging of batteries should not be undertaken casually. Through the charging cycle the
condition of the battery pack should be monitored and the charge cycle turned o at
completion or at the end of the recommended time.
How do I obtain the best life for the battery?
- Never allow the drill to come to a complete stand still before recharging. The battery
should be placed on charge whenever the battery is noticeably running down or the drill
no longer performs a task it previously performed.
- Avoid allowing lose items like screws or nails etc. to be stored with battery packs as these
or similar items can short battery packs and cause a re or explosion.
- Always unplug the charger when not in use and store in a dry secure place.
- Avoid charging or storing your battery in temperatures below 0ºC and above 45ºC.
How do I use the 2 gears on the drill?
To select the LOW gear (low speed, high torque setting), push the gear selector backward,
towards the back of the drill/driver. The number “1” will be displayed.
To select the HIGH gear (high speed, low torque setting), push the gear selector forward,
towards the chuck. The number “2” will be displayed.
NOTE: The gears cannot be changed if the variable speed / on o trigger (8) is depressed.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone LCD699-2SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone LCD699-2SC in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info