724656
15
Zoom out
Zoom in
Previous page
1/16
Next page
12v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: LCD699-2SC • 11/2017 • 54731
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
12v Lithium-ion Cordless Drill with Hammer Action
MODEL No.: LCD699-2SC • 11/2017 • 54731
26 27
Trouble Shooting Specications
Specications
Motor: 12 V
...
Low speed: n
0
-Lo = 0 – 400 min-
1
High speed: n
0
-Hi = 0 – 1300 min-
1
Impact Frequency: 0-6,000 / 0-19,500 BPM
Max. Torque: 25Nm
Drill/driver diam Ø: - Wood 25 mm
- Steel 10 mm
- Non aggregate materials: 10mm
Chuck: 10 mm Keyless
Battery (LY699-LI-12V): 12 V
... 1.5Ah/Li-Ion
Charger: Model: LYKC699-S
Input: 100-240VAC 50-60Hz 35W
Output: 12Vdc 2A
Charging time: Ready for use in 1 Hour
Product Dimensions: 190mm x 46mm x 190mm (L x W x H)
(Drill/driver with battery pack tted)
This product complies with:
1. Charger:
EMC:
EN 55014-1: 2006/+A1: 2009/+A2: 2011
EN 55014-2: 2015
EN 61000-3-2: 2014
EN 61000-3-3: 2013
General Requirements and Charger:
AS/NZA 60335.1: 2011 Inc A1+A2
AS/NZS 60335.2.29: 2004 Inc A1+A2
IEC 60335-1: 2010 (FIFTH EDITION) +A1:2013
IEC 60335-2-29: 2002 (FOURTH EDITION)
+ A1: 2004 + A2: 2009
Charger Safety Approval #:
SGS-160645
2. Drill:
AS/NZS 60745.1:2009
AS/NZS 60745.2.1:2009
AS/NZS 60745.2.2:2009
IEC60745-2-1:2003 Sec Ed +A1:2008
IEC60745-2-2:2003 Sec Ed +A1:2008
IEC60745-1:2006 Fourth Ed
EN 60745-1: 2009+A11
EN 60745-2-1: 2010
EN 60745-2-2: 2010
EMC:
EN 55014-1: 2006+A1:2009+A2:2011
EN 55014-2: 1997+A1:2001+A2:2008
3. Battery:
IEC 62133: 2012
EN 62133: 2013 (Battery Pack)
How do I adjust the torque?
The torque function will only operate when the screw function (15) is selected by rotating
the function selection collar (3) and aligning the screw symbol with the triangular indicator
on the top of the drill.
To adjust the torque setting you rotate the torque collar (2). The higher the number, the
higher the torque setting collar.
Controlling the torque allows for better control when using the drill/driver on specic add
screwing tasks and assists in preventing over-fastening and over-tightening.
For setting the torque position, rst select a low setting on the torque collar (2) and align
the selected symbol with the triangular indicator on the top of the drill/driver.
Slowly increase the torque setting to the desired level. It is suggested to test the setting on
scrap material rst.
How do I select hammer function?
Rotate the function selection collar (3) until the Hammer symbol aligns with the triangular
indicator.
How do I select drill function (Non Hammer)?
When using the drilling function the torque control has no eect to the output of the
drill. The drill function (16) is used when using the drill to drill holes in metal, non ferrous
material, wood, plastic and similar materials. Rotate the function selection collar (3) so
the symbol of the drill bit (16) aligns with the triangular indicator on the top of the drill
housing.
How do I select screw / driver function?
Rotate the function selection collar (3) so to align the screw symbol (15) with the triangular
indicator on the top of the drill housing. To adjust the torque setting, rotate the torque
setting collar (2). The higher the number, the higher the output torque. Align the required
torque setting number with the triangular indicator on the top of the drill. Torque setting
is 11.
What is the function of the Forward / Reverse switch?
This switch (6) will allow you to change the direction of the motor while the trigger switch
is not depressed.
Drill/driving uses the forward mode. The reverse mode is intended for the removal of
screws and assisting to remove jammed drill/driver bits.
What do I do if I have an issue with my drill?
If you have any issues with your drill/driver, please contact our Customer Service line on
1800 909 909.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone LCD699-2SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone LCD699-2SC in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info