724656
9
Zoom out
Zoom in
Previous page
1/16
Next page
12v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: LCD699-2SC • 11/2017 • 54731
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
12v Lithium-ion Cordless Drill with Hammer Action
MODEL No.: LCD699-2SC • 11/2017 • 54731
14 15
Fitting and removing the battery pack
1. To remove the battery (9) from the drill/driver, press the two side tabs on
the battery rmly and pull the battery from the drill/driver (Fig A).
2. To t the battery into the drill/driver, orientate the battery pack so the
side tabs of the battery are on the left and right side of the drill/driver,
and the small trim section of the pack is forward. Enter the battery into
the drill/driver aligning the ribs of the pack with the inner ribs of the drill/
driver. Push the battery all the way into the drill/driver handle without
forcing. The side tabs will “Click into place preventing the battery from
falling out (Fig B).
3. To t the battery (9) into the charger (10), orientate the battery so the side
tabs of the battery are to the sides of the charger and the small side of the
battery trim is towards the charger base indicators (11). Align the ribs of
the battery with the ribs of the charger base recess and insert the battery
all the way into the charger (Fig C). (The side tabs are not used).
4. To remove the battery (9) from the charger (10), lift the battery from the
charger without the need to depress the battery pack tabs.
Battery charging
IMPORTANT. Before attempting to charge the battery, check the charger
and the battery to ensure the charging equipment matches the battery
supplied. The components are all labelled with component numbers.
Check the input voltage on the charger label and ensure the input voltage
indicates 100-240V ac 50-60 Hz.
CAUTION! The rechargeable battery may not be fully charged on leaving
the factory. Charge the rechargeable battery for approx. 1 hour before rst
use, or until fully charged as indicated by the red light (11a), going o on
the charger, and the green ready to use light (11b) is glowing continually.
CAUTION! The working temperature of the charging operation is 0°C to 45°C.
NOTE: If the battery pack is incorrectly orientated the battery will not fully
enter the base as depicted.
1. Plug in the charger (10) and switch on at the power supply. The GREEN LED
power indicator (11b) located on the charger base will ash constantly to
indicate that the charger has power connected to it and there is no battery
(9) inserted in the charger (10).
2. Align the battery (9) with the charger (10). Insert the battery pack and slide
it rmly into position (Fig C).
The RED LED charging indicator (11a) on the charger will light up during
the charging process and the green ashing power indicator (11b) will turn
OFF. When the battery is charged and ready for use, the RED light (11a) will
go o, and the green light (11b) will glow constantly indicating the battery
inserted in the charger (10) is ready for use.
The battery will be ready for use up to approximately 1 hour.
The GREEN light (11a) will remain on in a solid condition until the battery
(9) is removed or the power supply to the charger (10) is turned o.
If the battery (9) is removed and the power supply to the charger (10) is left
on, the green light (11b) will ash until a battery (9) is inserted or the power
supply to the charger (10) is turned o.
NOTE: The power to the charger should be turned
o when unattended, with or without a battery
inserted.
2 Speed gearbox
The 2 Speed Gearbox allows you to select a gear
with the optimum speed and torque to suit the
application.
NOTE: When changing the drill/driver selector
ensure the drill/driver is not operating.
1. To select the LOW gear (low speed, high torque
setting), push the gear selector (4) backward,
towards the back of the drill/driver. The number “1” will be displayed (Fig D).
2. To select the HIGH gear (high speed, low torque setting), push the gear
selector (4) forward, towards the chuck. The number “2” will be displayed
(Fig D).
Battery Fitting / Battery Charging Speeds
A. B. C.
2
1
The picture here shows the gear
selector forward so the drill/driver
is in High speed, with the number 2
displayed.
D.
PUSH IN
BOTH TABS
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone LCD699-2SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone LCD699-2SC in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info