724656

Workzone LCD699-2SC Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
12v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL No.: LCD699-2SC • 11/2017 • 54731
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
12v Lithium-ion Cordless Drill with Hammer Action
MODEL No.: LCD699-2SC • 11/2017 • 54731
18 19
When using the drill/driver for drilling
1. When using the drilling function the torque
control has no eect to the output of the drill.
The drill function (16) is used when using the
drill to drill holes in metal, non ferrous material,
wood, plastic and similar materials.
Rotate the function selection collar (3) so the
symbol of the drill bit aligns with the triangular
indicator on the top of the drill housing (Fig H).
When using the drill/driver for Hammer drilling
1. When using the hammer drilling function (14),
the torque control has no eect to the output of
the drill. The hammer drill function (14) is used
when using the drill to drill holes in non red,
and non aggregate, but cement based material
or similar materials. The action of the hammer is
for drilling and not for chiseling.
When tting the drill bit, ensure to use a
masonry drill bit suitably designed for the
application.
Rotate the function selection collar (3) so the symbol of the hammer
function (14) aligns with the triangular indicator on the top of the drill
housing (Fig I).
Inserting and removing bits
This drill/driver has a keyless chuck, which
means that a chuck key is not needed to secure
a bit in the drill/driver.
1. Open the chuck (1) by unscrewing it in an anti-
clockwise direction, holding the drill/driver as
shown (Fig J).
Do this suciently enough to allow the drill/
driver bit to enter the jaws of the chuck.
2. Ensure the drill/driver bit is fully inserted, so
that the chuck jaws grip the straight section of
the bit.
Drill/driving uses the forward mode. The reverse mode is intended for the
removal of screws and assisting to remove jammed drill/driver bits.
Adjustable torque
This drill/driver is equipped with 21 torque settings plus 1 x drill setting, 1 x
screw setting and 1 x hammer setting.
The torque settings are controlled and adjusted by the torque setting collar
(2), but only eects the output when the screw function (15) is selected.
The screwdriving function, the drill function and the hammer function are
all selected using the second collar, the function selection collar (3).
When using the drill/driver for Screwdriving
1. Rotate the function selection collar (3) so to align the screw symbol with
the triangular indicator on the top of the drill housing (Fig G). Function
setting is screw function (15).
2. To adjust the torque setting, rotate the torque setting collar (2). The
higher the number, the higher the output torque. Align the required
torque setting number with the triangular
indicator on the top of the drill (Fig G). Torque
setting is 11.
Controlling the torque allows better control
when using the screw function (15) when
applying screws and assists in the prevention of
over tightening if the torque is correctly set.
For setting the torque position, always start o
with a low torque setting and build up to the
required higher torque setting after testing on
a test piece rst.
Forward/Reverse Inserting//Removing bits
I.
H.
J.
OPEN
CLOSE
G.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone LCD699-2SC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone LCD699-2SC in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info