481030
10
Zoom out
Zoom in
Previous page
1/22
Next page
POWXQ5360 EN
Copyright © 2010 VARO P a g e | 10 www.varo.com
Fig 9
NOTE: The blade guard and splitter must always be correctly aligned so
that the cut work piece will pass on either side of the splitter without
binding or twisting to the side.
Improper alignment of the splitter can cause “kickback” and serious injury.
8.5 Adjusting riving knife
There must be a clearance of about 5 6 mm between the riving knife and the blade teeth
when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first
loosening clamping nut by hand counterclockwise and then loosening hex bolt
counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,
securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that
the riving knife is secured and that the top blade guard works smoothly before cutting.
The riving knife has been installed before shipment from the factory so that the blade and
riving knife are in a straight line after your simple set-up. Refer to the section titled
“Repositioning riving knife” for the set-up.
CAUTION:
If the blade and riving knife are not aligned properly, a dangerous pinching condition may
result during operation. Make sure the riving knife is positioned between both outer ends
of the blade teeth when viewing from the top. You could suffer serious personal injury
while using the tool without a properly aligned riving knife. If they are not aligned for any
reasons, always have an authorized service center repair it.
When adjusting the riving knife clearance from the blade teeth, always loosen the hex bolt
only after loosening the clamping nut.
8.6 Assembling the table extension wings (fig 10, fig 11)
Fig 10
Fig 11
8.6.1 Side extension table
Unscrew the screws (a) at the end of both extension tubes.
Install the side extension table by sliding the tubes into the 2 holes (b) at the side of the
main table.
Replace the screws (a) back into the tubes to prevent you from pulling the side table too
far out.
You can lock at the wanted position with the 2 locking knobs (c) at the bottom of the main
table.
b
a
c
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5360 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5360

Powerplus POWXQ5360 User Manual - German - 22 pages

Powerplus POWXQ5360 User Manual - Dutch - 23 pages

Powerplus POWXQ5360 User Manual - French - 21 pages

Powerplus POWXQ5360 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info