481030
20
Zoom out
Zoom in
Previous page
1/22
Next page
POWXQ5360 EN
Copyright © 2010 VARO P a g e | 20 www.varo.com
Sympton
Possible causes
Corrective action
The material pinches
the blade when ripping
The rip fence is not aligned
with the blade.
Check and adjust the rip fence.
The wood is warped, or the
edge that is against the fence
is not straight.
Select another piece of wood.
The material binds on
the splitter
The splitter is not aligned
correctly with the blade.
Check and align the splitter with
the blade.
The saw makes
unsatisfactory cuts
The blade is dull.
Replace the blade.
The blade is mounted
backwards.
Turn the blade around.
There is gum or pitch on the
blade.
Remove the blade and clean it
with turpentine and coarse steel
wool.
The blade is not appropriate
for the work that is being
done.
Change the blade.
There is gum or pitch on the
table causing erratic feeding.
Clean the table with turpentine
and coarse steel wool and apply a
coat of automotive polishing wax.
The material kicks back
from the blade
The rip fence is out of
alignment.
Align the rip fence with the miter
gauge slot.
The splitter is not aligned
correctly with the blade.
Align the splitter with the blade.
The work piece is being fed
without the rip fence.
Install and use the rip fence.
The splitter is not in place.
Install and use the splitter (with
the guard)
The blade is dull.
Replace the blade.
The operator is letting go of
the material before it has
passed the saw blade.
Push the material all the way past
the saw blade before releasing
the work piece.
The miter angle locking knob
is loose.
Tighten the knob.
The blade does not
raise or tilt freely
There is sawdust and/or dirt
in the raising and tilting
mechanisms.
Brush or blow out any loose dust
and dirt.
The blade does not
reach full speed
The extension cord is too
light or too long.
Replace with the proper size of
extension cord.
The voltage from the outlet is
too low.
Contact the electricity supplier.
The saw vibrates
excessively
The saw is not mounted
securely to the workbench.
Tighten all mounting hardware.
The stand is on an uneven
surface.
Reposition the table saw on a flat
level surface.
The blade is damaged.
Replace the blade.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWXQ5360 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWXQ5360 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWXQ5360

Powerplus POWXQ5360 User Manual - German - 22 pages

Powerplus POWXQ5360 User Manual - Dutch - 23 pages

Powerplus POWXQ5360 User Manual - French - 21 pages

Powerplus POWXQ5360 Additional guide - All languages - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info