538892

Zelmer 13Z011 Manual

210
Zoom out
Zoom in
Previous page
1/228
Next page
210
Carefully remove the brewing head unit (14). Press the protrusion (26) with your thumb (see fi g. 2) and fi rmly grasp the
handle (14a) with the other four fi ngers and take out the brewing head unit according to the directions of the arrows in fi g. 4
(fi rst a gentle upward movement and next a horizontal movement). Be careful when inserting the heat unit (14) back into
place: holding the handle (14a) direct the head unit (14) on the protrusion (23) (see fi g. 2), next push gently in the horizon-
tal direction to the center of the coffee maker and next vertically downwards (see arrows in fi g. 5).
Fig. 4 Fig. 5
Fig. 6
The brewing unit (14) is inserted properly if the coupling of the brewing head unit axis (14g)
is on the shaft under the head unit (14h) (fi g. 3). Gently close the door (15). Do not use
force, if you cannot close the door. The brewing head (14) might not be installed prop-
erly. In such a case, remove the brewing head again according to the instructions above.
Check if the brewing head unit mechanism is in the START position. This means that
the axis of symmetry of the triangle on the right side ◄ (the X line) should be be-
tween the two verticals of the two triangles on the left side ▼ ▲ (fi g. 6).
If for any reason (e.g. due to cleaning) the brewing head unit is not in the START position, turn the unit axis cou-
pling (14) (fi g. 6) to the right or to the left using the key (25) to set the “starting” position (fi g. 6).
If the shaft inside the coffee maker (14h) is turned e.g. during cleaning, it needs to be reset properly using the
other end of the brewing unit key (25). Never turn the coupling more than half a turn. Never use force while turning
the key (25). Now try to insert the brewing head unit (14) again.
Warning: The brewing head unit (14) may be blocked if the coffee maker service door (15) is not completely open
or is not properly and completely closed.
5. Before initial use – tips
Unpack the appliance and remove all packaging materials. Never leave any plastic bags or polystyrene, etc. in the ●
reach of children as they may pose a threat to them.
Place the coffee maker on a fl at surface, away from any heat or water source. Make sure there is at least 10 cm of free ●
space around the appliance and 20 cm above the appliance.
Never install the coffee maker in environments in which the temperature may fall below 3°C, because freezing water ●
may damage the pipes and elements inside the appliance. Keep the appliance away from direct sunlight and excessive
heat.
Take out the measuring spoon ● (24), the brewing head unit key (25), the fl oat (3a) and the fl oat plug (3b) out of the
water tank. The elements are wrapped in a plastic foil. Insert the fl oat (3a) and the fl oat plug inside the water tank (3).
Check if the brewing head unit (14), the dregs box (22) and the drip tray (19) together with the drip tray grill (21) are in
their proper places (fi g. 7).
ATTENTION! Remove the self-adhesive transport tape from the drip tray (19) and the drip tray grill (21). ●
Rinse the water tank ● (3), wipe the bean coffee container (4) clean with a damp cloth.
Set the water hardness, following the directions in chapter ● 16.7 “Setting the Water Hardness”.
NOTE! Each coffee maker is checked in the factory before shipping using bean or ground coffee. Therefore ●
the possibility of coffee remains inside the appliance is a normal situation. It is recommended to pour out
2 fi rst cups of coffee when using the coffee maker for the fi rst time.
CAUTION! Never fi ll the water tank (3) with hot water, mineral water or other liquids. Use only cold, fresh water. ●
The water tank (3) can be removed to fi ll it with water by lifting it upwards.
Putting bean coffee or any other food products or liquids inside the ground coffee container by accident may result in ●
damage to the coffee maker.
Make sure the ● fl oat (3a) is still in the left corner of the water tank (3). It is a sensor informing about the current water level.
Fill the water tank ● (3) with water before the initial use of the coffee maker (see chapter 6).
… 210 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Zelmer 13Z011 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Zelmer 13Z011 in the language / languages: English, Polish as an attachment in your email.

The manual is 15,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info