802116
29
Zoom out
Zoom in
Previous page
1/79
Next page
EN
5110326C_OI-II_Webasto Live 17
6Installation and electrical
connection
Observe the safety information provided here chapter2,
"Safety" on page 14.
NOTE
In addition to these operating and installation instruc-
tions, follow and comply with the local regulations re-
lating to operation, installation and environmental
protection.
6.1 Requirements installation space
The following points must be take into account when se-
lecting the installation location for the Webasto Live:
The lower edge of the enclosed mounting template
must be a minimum distance above the ground during
installation. The minimum distance is indicated in the
figure at chapter13, "Assembly" on page 22.
If several charging stations are installed next to each
other, a spacing of at least 200 mm must be main-
tained between each station.
The mounting surface must be solid and strong.
The mounting surface must be completely flat (max. 1
mm difference between the individual mounting
points).
The mounting surface must not contain any flam-
mable substances.
The normal parking position of the vehicle.
The location of the charging plug on the vehicle.
A cable run from the charging station to the vehicle as
short as possible.
No risk of driving over the charging cable.
Possible electrical connections.
Pavements and escape routes must not be obstructed.
Reception via WLAN or UMTS exists.
Protected against direct solar radiation and rain for
optimum and fault-free operation.
Compliance with local regulations such as garage reg-
ulations or fire protection regulations.
6.2 Criteria for the electrical connection
The maximum charging current that can be configured is
indicated on the type label of the charging station. The
type label is on the right-hand side of the charging sta-
tion.
The power availability in the service connection determ-
ines the maximum permitted charging current. The elec-
trician makes the necessary settings in the configuration.
(see online configuration instructions: https://webasto-
charging.com/documentation)
Before connecting, have the prerequisites for connection
checked by an electrician. Comply with the nationally ap-
plicable regulations of the authorities and power supply
companies, e.g. registration of installation of a charging
station.
All protective devices specified must be designed such
that every power supply pole of the charging station is
disconnected in the case of a fault. When selecting the
protective device, you must use the national installation
regulations and standards.
6.2.1 Dimensioning of the Residual Current
Circuit Breaker (RCCB)
The national installation regulations generally apply. Un-
less otherwise specified therein, each charging station
must be protected by an appropriate residual current
device (RCD) with a trip current of ≤30mA.
Suitable residual current devices are a type-B RCD or a
type-A RCD with a residual direct current detecting
device (RDC-DD) according to IEC62955. A suitable type-
A RCD with integrated residual DC detection is, for ex-
ample, the residual circuit current breaker type
DFS4AEV from Doepke.
The rated residual current must not be greater than
30mA. Whenever a charging station is protected using a
Type B ground fault circuit interrupter (GFCI), every up-
stream GFCI, even if not assigned to the charging station,
must either by a Type B unit, or be equipped with a DC
ground fault detection unit.
6.2.2 Dimensioning of the circuit breaker
The circuit breaker must conform to IEC 60898. The let-
through energy (I²t) must not exceed a maximum 80,000
A²s.
Alternatively, a residual current circuit breaker combina-
tion (RCBO) according to EN 61009-1 can be used. The
aforementioned parameters apply for this circuit breaker
combination.
6.2.3 Mains isolation device
The charging station does not have its own main ON/OFF
switch. The protective devices installed in the power sup-
ply system are therefore also used to disconnect the
power supply.
6.2.4 Dimensioning the cross section of the lead
The electrician determines the conductor cross section,
see chapter14, "Technical data" on page 23.
The cross section of the lead is dependent on:
the maximum power availability from the service con-
nection.
the length of the cable.
6.3 Installation
See also chapter13, "Assembly" on page 22. The sup-
plied installation material is intended for mounting the
charging station on a concrete wall or on an external
stand. For installation on a stand, the mounting material
is included in the scope of delivery of the stand.
üScope of delivery is checked for completeness.
uTake into account the mounting position at the install-
ation location. See Fig. 14.
uRemove the drill template at the perforation from the
packaging.
uMark the four positions of the drill holes at the install-
ation location using the drill template. See Fig. 14.
uDrill 4x8mm drill holes in the marked positions.
uMount the wall-mounting bracket in position over the
upper holes using 2 wall plugs and 2 screws,
6x70mm, T25.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Webasto Live at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Webasto Live in the language / languages: English, German, Dutch, Italian, Spanish as an attachment in your email.

The manual is 7.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Webasto Live

Webasto Live User Manual - Danish, Swedish, Norwegian, Finnish - 67 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info