667340
43
Zoom out
Zoom in
Previous page
1/544
Next page
0478 111 9917 F - EN
9
DEEN
FR
NLITESPTNOSV
DA
PLSL
HU
HR
CS
Press
12= apron onto the
9= guard bar using the clips
(located on the under-
side of the apron) at the
positions indicated by a
triangle in the illustration.
NOTE
The apron seam must lie
evenly on the guard bar to
prevent additional strain on
the apron.
NOTE
Top up engine oil before in-
itial start (see engine in-
struction manual).
Please consult the engine
instruction manual for the
type of engine oil to be
used and the filling quantity.
NOTE
The appliance is a high
grass mower and may only
be used for mowing grass.
Fuel and engine oil
9
Checking engine oil
Check the engine oil level at
regular intervals. Allow the
mower to stand in the hori-
zontal position for approx.
2 min. so that all the oil can
collect in the bottom of the
engine. The further procedure
can be found in the engine in-
struction manual.
Fuel
Always use
fresh good quality fuel, nor-
mal unleaded petrol.
(see engine instruction ma-
nual).
Notes on mowing
Applications
Working on slopes
For safety reasons, the appli-
ance must not be used on
slopes with an incline of more
than 25° (46.6 %). It is only
permitted to work across the
direction of the gradient and
never up or down the slope, in
order to prevent loss of con-
trol of the lawn mower.
Risk of injury!
A slope inclination of 25° cor-
responds to a vertical height
increase of 46.6 cm for a
100 cm horizontal surface.
In order to ensure an ade-
quate oil supply for the en-
gine, the information in the
accompanying engine instruc-
tion manual must be additio-
nally observed when using
the machine on slopes.
max. 25°
100
46.6
Set cutting height 1
(see section “Setting the
cutting height”).
Step
Onto each of the threads
of the
9= guard bar, screw one
10= nut as far as possible, as
shown.
Push on
16= angle piece.
Guide
9= guard bar with apron
under the front
suspension and insert in
the
24= slots on both sides of the
lawn mower.Ensure
correct positioning of the
16= angle piece. Attach
11= washers and fasten the
guard bar using
10= nuts (35-40 Nm).
3
Step
5
Step
Attach
12= apron as shown to all
three
13= screws.
Using a finger, press the
bolt against the mowing
deck housing from
below. A the same time,
ensure that the square
part of the bolt engages
in the square hole in the
mowing deck housing.
Fasten
14= nuts (8-10 Nm).
52= Press protective caps
onto screws.
4
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking MB 6RV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking MB 6RV in the language / languages: All languages as an attachment in your email.

The manual is 35,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Viking MB 6RV

Viking MB 6RV User Manual - German - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info