667349

Viking GE 150 Manual

43
Zoom out
Zoom in
Previous page
1/548
Next page
41
DEFRNLITESPTNOSVFIDAPLSLSKHU EN
0478 201 9906 D - EN
9.2 Safety interlock
The motor/shredding tool may only be
operated when the feed chute has been
properly closed. If the right closure screw
(machine viewed from the front) becomes
loose during operation, the motor is
switched off automatically and after a few
seconds the shredding tool comes to a
standstill.
9.3 Motor run-down brake
The motor run-down brake shortens the
run-down time from when the machine is
switched off until the blades stop to a few
seconds.
9.4 Protective covers
The garden shredder is equipped with
protective covers in the feeding and
ejection areas. These include the
complete feed chute with the upper chute
and splash guard, the ejection chute
extension and the discharge flap.
The protective covers ensure that a safe
distance is maintained from the shredding
blades.
10.1 Electrical connection of garden
shredders
The power cable must be adequately
protected by fuse. (Ö 18.)
Only electric cables which are no lighter
than rubber sheathed cables
H07 RN-F DIN/VDE 0282 may be used.
The minimum cross-section of the power
cable must be 3x1.5mm² for a length of
up to 25 m or 3x2.5mm² for a length of
over 25 m.
The connectors of the electric cable must
be made of rubber or have a rubber cover
and conform to the standard
DIN/VDE 0620.
A CEE plug device and a 5-wire cable
must be used for three phase models.
The plug connections must be splash
proof.
Unsuitable extension cables lead to a loss
of power and may result in damage to the
motor.
GE 150, GE 250, GE 250 S:
This machine is intended for operation with
a power supply having a system
impedance of Z
max
at the transfer point
(house connection) of maximum
0.443 ohms (at 50 Hz).
The user must ensure that the machine is
only operated with a power supply which
meets this requirement.
If necessary, this information can be
obtained from the local electric power
company.
10.2 Connecting the power cable
GE 150, GE 250, GE 250 S:
● Lift clip (1).
● Connect power cable connector.
● Release clip.
GE 260, GE 260 S:
● Connect the power cable connector to
the 5-pin mains plug on the machine.
10.3 Switching on the garden
shredder
● Connect the power cable. (Ö 10.2)
● Press the green button (1) on the switch
(illus. shows GE 150, GE 250,
GE 250 S).
The garden shredder starts up.
10. Operating the machine
Risk of injury:
Carefully read the section entitled
"For your safety" (Ö 4.) and follow
all the safety instructions before
operating the garden shredder.
Risk of injury!
Observe the instructions in section
"Warning – dangers caused by
electrical current" (Ö 4.2).
When choosing a power cable, take
account of all the information in the
"Electrical connection" section
(Ö 10.1).
There must be no shredding
material in the machine when it is
switched on as it may be expelled.
The blade disc locking device must
always be tilted back to the stop.
(Ö 11.4)
Only begin to feed the shredding
material once the motor has
reached the maximum speed (idling
speed).
9
10
… 43 …


Need help? Post your question in this forum.

Forumrules
1

Forum

viking-ge-150

Reset search

  • Where is the rest locking device on a Viking GE150 shredder please?
    Submitted on 2-4-2022 at 11:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking GE 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking GE 150 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info