Manual Viking GE 150 (page 41 of 548) (All languages)

667349

Zoom out

Zoom in

1/548

DEFRNLITESPTNOSVFIDAPLSLSKHU EN

0478 201 9906 D - EN

7.2 Installing the chassis and

ejection chute

1 Install the ejection chute

extension

● Place the basic unit (A) onto a block of

wood with a height of approx. 15-

20 cm.

● Engage the hooks (1) of the ejection

chute extension (O) into the

openings (2) on the rear of the basic

unit (A) and turn the extension

downwards so that the front part of the

basic unit is precisely inserted in the

opening of the ejection chute extension.

● Fasten the screws (U) in the lugs of the

hooks (1) (1 - 2Nm).

2 Attach the chassis

● Press square nuts (K) and washers (L)

in the recesses provided on the basic

unit (3).

● Push the chassis with both wheel

carriers (4) up to the stop in the guides

on the basic unit (5).

● Push bent section of wheel carrier (6)

into the recess on the ejection chute

extension (7).

● Insert the screws (M) with washers (L)

the openings in the wheel carriers (8)

and fasten using combination

spanner (V) (4 - 6Nm).

3 Install strip

● Position the strip (P) and fasten

screws (R) (1 - 2Nm).

● Lift machine into upright position.

4 Install the discharge flap

● Attach the discharge flap (N) and press

in pin (Q) (use a plastic hammer if

necessary).

Ensure that the ribs (9) inside the

discharge flap on the left and right are

all correctly located in the guide groove

of the ejection chute extension (10).

7.3 Opening and closing the

discharge flap

Opening the discharge flap:

● For shredding, fold the discharge

flap (1) upwards and allow the tab (2) to

engage in the ejection chute extension.

Closing the discharge flap:

● For transport or space-saving storage,

lift the tab (2) slightly and fold away the

discharge flap (1) downwards.

7.4 Installing upper chute

● Place the upper chute (S) onto the

lower chute (3) with the symbol (1)

facing forwards in the direction of the

closure screws (2).

● Fasten the screws (T) in the order

shown (1 2 3 4).

8.1 What material can be processed?

– Feeding the garden shredder. (Ö 8.8)

GE 150, GE 250 S, GE 260 S:

Tree and hedge cuttings and thick branch

material with side shoots.

GE 250, GE 260:

Organic plant trimmings such as fruit and

vegetable cuttings, flower cuttings, leaves,

tree and hedge cuttings, as well as thick

branches with side shoots and twigs.

8.2 What material cannot be

processed?

Stones, glass, bits of metal (wire, nails,

etc.) or plastic must not be fed into the

garden shredder.

As a general rule:

Any materials that do not belong on the

compost heap should not be processed

using the garden shredder.

8.3 Maximum branch diameter

The data relates to freshly cut branch

material:

Maximum branch diameter

GE 150, GE 250, GE 250 S: 35 mm

GE 260, GE 260 S: 40 mm

The bent section of the wheel

carrier (6) must be precisely

inserted in the recesses on the

ejection chute extension (7).

The funnel can only be installed by

a specialist dealer using special

tools. VIKING recommends VIKING

specialist dealers.

In order to prevent the splash guard

from slipping off, we recommend

that the indicated assembly

sequence be observed.

8. Notes on working with the

machine

Tree and hedge cuttings should be

processed when fresh, as the

shredding performance is better

with fresh than with dried-out or wet

material.

Where is the rest locking device on a Viking GE150 shredder please?
Submitted on 2-4-2022 at 11:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Viking GE 150 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Viking GE 150 Manual

Product: