667349
42
Zoom out
Zoom in
Previous page
1/548
Next page
0478 201 9906 D - EN
40
8.4 Working area for operator
For safety reasons, the operator
must stay within the working area
(grey area X) for the entire operating
period (while the motor is switched on
or the engine is running), particularly in
order to prevent injuries due to
shredding material that is ejected
backwards.
8.5 Correct machine load
The load on the motor or engine of the
garden shredder must never cause the
speed to drop significantly. Always feed
the garden shredder continuously and
steadily. If the speed drops when working
with the garden shredder, stop feeding the
machine in order to relieve the load on the
motor or engine.
8.6 Overload protection
If an overload of the motor occurs during
operation, the built-in overload protection
device automatically switches off the
motor.
The garden shredder can be started up
again after a cooling period of
approx. 10 minutes. Frequent triggering
of the overload protection may be
attributable to the following causes:
Unsuitable electric cable (Ö 10.1)
Power overload
Machine overloaded due to excessive
quantities of shredding material or blunt
blades
8.7 If the cutting unit of the garden
shredder is blocked
If the cutting unit of the garden shredder
becomes blocked during shredding,
immediately switch off the motor and
disconnect the power cable. Then remove
the feed chute and eliminate the cause of
the fault.
8.8 Feeding the garden shredder
Before feeding the garden shredder,
note the working area. (Ö 8.4)
Start the garden shredder. (Ö 10.3)
Soft material:
Throw organic plant trimmings such as
fruit and vegetable waste, flower
cuttings, leaves, thin branches etc. into
the feed opening (1).
Hard material:
Feed tree and hedge cuttings as well as
branch material slowly into the feed
opening (1). The hard material is
automatically drawn in by the machine.
9.1 Motor restart inhibitor
The machine can only be started via the
switch and not by plugging the electric
cable into the mains socket.
Only switch off the motor when
there is no longer any shredding
material in the machine. Otherwise,
the blade disc may become blocked
when operation is resumed.
7
Risk of injury!
Carefully read the section entitled
"For your safety" (Ö 4.), sub-
section "Working with your
machine" (Ö 4.6) in particular, and
follow all the safety instructions
before feeding the garden
shredder. It is only permitted for
one person to feed the garden
shredder.
Risk of injury!
Never reach into the feed
opening.
8
Damp or wet soft material will
cause blockages in the machine
more quickly. For this reason, feed
the garden shredder more slowly
and pay particular attention to the
motor speed. It should not drop
during feeding.
Cut up thick branches and
branches with side shoots (note the
maximum branch thickness
(Ö 8.3)) beforehand using loppers.
Risk of injury!
The inclined blade unit can cause
branches to kick back.
In order to prevent injuries caused
by kickback, the garden shredder
must be fed with hard material in
the correct manner:
Insert longer branches at a slight
angle and guide them along the
right-hand chute wall to the blade
unit in accordance with the
symbol (2).
Observe the correct motor load.
(Ö 8.5)
9. Safety devices
42


Need help? Post your question in this forum.

Forumrules
1

Forum

viking-ge-150

Reset search

  • Where is the rest locking device on a Viking GE150 shredder please?
    Submitted on 2-4-2022 at 11:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking GE 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking GE 150 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info