667349

Viking GE 150 Manual

45
Zoom out
Zoom in
Previous page
1/548
Next page
43
DEFRNLITESPTNOSVFIDAPLSLSKHU EN
0478 201 9906 D - EN
Never spray water onto
motor or engine components,
seals, bearing points or
electrical parts such as
switches. This would result in
expensive repairs.
If you are unable to remove
the dirt and accumulated
deposits with a brush, a damp
cloth or a stick, VIKING
recommends the use of a
special cleaner (e.g. STIHL
special cleaner).
Do not use aggressive cleaning agents.
Clean the blade discs regularly.
11.2 Installing the feed chute
● Attach feed chute (1) to fastening hooks
on the basic unit (2) and pivot forwards.
● Tighten both closure screws (3)
simultaneously.
11.3 Removing the feed chute
● Loosen both closure screws (1)
until they turn freely. They remain
on the feed chute
● Pivot the feed chute (2) to the rear and
remove.
11.4 Locking the blade disc
● Remove the feed chute. (Ö 11.3)
● Turn blade disc (1) to that the
recess (2) is located in front of the
locking device (3).
● Fold up the locking device (3).
11.5 Removing the blade set
● Lock the blade disc (5). (Ö 11.4)
● Loosen screw (1) with
combination spanner (V).
● Remove the screw (1), retaining
washer (2), clamping ring (3), wing
blade (4), wing blade (6, only on
GE 250 and GE 260) and blade
disc (5).
● Remove the reversible blade. (Ö 11.8)
● GE 250 and GE 260: Unscrew
screws (7) and remove together with
nuts (9). Remove the shredding
blades (8) downwards.
11.6 Installing the blade set
● Attach the reversible blade to the blade
disc. (Ö 11.7)
● GE 250 and GE 260: Position the
shredding blades (8) on the underside
of the blade disc (5) and fasten with
nuts (9) and screws (7) (10 Nm).
● Insert the blade disc (5) into the
housing and fasten. (Ö 11.4)
● Fit the wing blade (6, for GE 250 and
GE 260 only), wing blade (4), clamping
ring (3) and retaining washer (2) and
fasten with screw (1) (50 Nm).
● Fold back the locking device so that the
blade disc can turn freely again.
(Ö 11.4)
● Install the feed chute. (Ö 11.2)
11.7 Blade maintenance
Maintenance interval:
Before each use
● Remove the feed chute. (Ö 11.3)
● Lock the blade disc. (Ö 11.4)
● Check the blades for damage (notches
or cracks) and wear; reverse or replace
if necessary.
Wear limits of the blades:
The closure screws must be
securely fastened to the feed chute.
14
15
Risk of injury:
Always wear gloves.
Do not touch the blades
until they have come to a
standstill.
The installation sequence and
specified tightening torques must
always be observed.
16
17
17
Risk of injury!
Always wear thick
gloves.
The blades must be reversed or
replaced before the specified wear
limits are reached. VIKING
recommends VIKING specialist
dealers.
18
… 45 …


Need help? Post your question in this forum.

Forumrules
1

Forum

viking-ge-150

Reset search

  • Where is the rest locking device on a Viking GE150 shredder please?
    Submitted on 2-4-2022 at 11:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Viking GE 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Viking GE 150 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info