Manual Viking GE 150 (page 46 of 548) (All languages)

667349

Zoom out

Zoom in

1/548

0478 201 9906 D - EN

1 Reversible blades

● On the blades, measure the

distance (A) between the bore and the

edge of the blade at several points.

Minimum distance:

A=6mm

2 Wing blade

● Measure the blade width (B) at the

upward-pointing curved edge of the

wing blade.

Minimum blade width:

B=15mm

3 Wing blade (GE 250, GE 260)

● Measure the blade width (C) at the

upward-pointing curved edge of the

wing blade.

Minimum blade width:

C=19mm

4 Shredding blade (GE 250, GE 260)

● Measure the blade width (D) at the

upward-pointing curved edge of the

shredding blade.

Minimum blade width:

D=13mm

11.8 Reversing the blades

● Remove the blade set. (Ö 11.5)

● Unscrew screws (1) and remove

together with nuts (2).

● Remove blade (3) upwards.

● Clean the blade disc.

● Reverse blade (3) and place onto the

blade disc with the sharp edge exposed

and align the bores.

● Insert screws (1) through the bores and

screw on nuts (2). Tighten the nuts (2)

to 10 Nm.

● Install the blade set. (Ö 11.6)

Sharpening the blades:

Blades which are blunt on both sides must

be sharpened before resuming work.

In order to ensure optimum machine

operation, the blades should only be

sharpened by a technician. VIKING

recommends VIKING specialist dealers.

● Remove the blades for sharpening.

● Cool the blades when sharpening,

e.g. with water. The blade must not be

allowed to display blue colouring, as

this would reduce its cutting quality.

● Sharpen the blade evenly to prevent

vibrations due to imbalance.

● Check blades for damage before

installing: The blades must be replaced

if notches or cracks are visible or if the

blades have reached the wear limits.

● Sharpen blades at a sharpening angle

of 30°.

● Sharpen the blades against the cutting

edge.

● After sharpening, remove any

sharpening burr at the cutting edge

using fine sandpaper.

● Observe the tightening torques

contained in the "Reversing the blades"

section when installing the blades.

11.9 Electric motor and wheels

The electric motor is maintenance-free.

The wheel bearings are maintenance-free.

11.10 Storage and winter break

Store the garden shredder in a dry and

locked place that is generally free of dust.

Make sure that the machine is kept out of

the reach of children.

Only store the garden shredder in good

operating condition and with the feed

chute fitted.

Note the following points when storing the

garden shredder for extended periods

(over winter):

● Thoroughly clean all external parts of

the machine.

● Thoroughly lubricate/grease all moving

parts.

12.1 Pulling or pushing the

garden shredder

● Hold the garden shredder at the

upper chute (1) and tilt to the rear.

● The garden shredder can be pulled or

pushed slowly (walking pace).

Blunt reversible blades may only be

reversed once. Always reverse

both blades.

12. Transport

Risk of injury!

Before transporting, carefully read

and observe the section "For your

safety", in particular the

"Transporting the machine" section.

(Ö 4.4)

Where is the rest locking device on a Viking GE150 shredder please?
Submitted on 2-4-2022 at 11:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Viking GE 150 in the language / languages: All languages as an attachment in your email.

The manual is 18,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Viking GE 150 Manual

Product: