815507
17
Zoom out
Zoom in
Previous page
1/56
Next page
1717 3-90-30007498Vermont Castings • Radiance RADVT Installation Manual_R32 • 10/23
WARNING
!
RiskofFire/Explosion/Asphyxiation! Improper support
may allow vent to sag and separate. Use vent run supports
and connect vent sections per installation instructions. DO
NOT allow vent to sag below connection point to appliance.
Figure 3.6 - Securing Vertical Pipe Sections
Figure 3.7 - Securing Horizontal Pipe Sections
DisassembleVentSections:
To disassemble any two pieces of pipe, rotate either section,
Figure 3.8, so that the seams on both pipe sections are
aligned, Figure 3.9. They can then be carefully pulled apart.
Figure 3.8 - Rotate Seams for Disassembly
Figure 3.9 - Align and Disassemble Vent Sections
Horizontal Termination Cap:
WARNING
!
Risk of Fire! The telescoping flue section of the
termination cap MUST be used when connecting vent.
1-1/2” (38 mm) minimum overlap of vent and
telescoping ue section is required.
Failure to maintain overlap may cause overheating and
re.
Note:Forhorizontalventrunsthroughacombustible
wall and framing dimensions, refer to appliance
installation manual.
Install the Horizontal Termination Cap
Attach slip section of cap to last vent section. Maintain 1-1/2”
overlap between slip and vent sections.
Note: For installations using black pipe, slide the
decorativewall thimble over the last vent pipebefore
connecting the termination to the pipe. When this
connectionhasbeenmade,slidethewallthimbleupto
the interior wall surface and attach with screws provided.
Secure termination cap to exterior wall using provided holes
and fasteners.
Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
Flash and seal as appropriate for siding material at outside
edges of cap.
When installing a horizontal termination cap, follow the cap
location guidelines as prescribed by current ANSI Z223.1
and CAN/CGA-B149 installation codes.
CAUTION
!
Risk of Burns! Local codes may require installation of a
termination guard to prevent anything or anyone from
touching the hot cap.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vermont Castings Radiance Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Radiance Series in the language / languages: English as an attachment in your email.

The manual is 6.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Radiance Series

Vermont Castings Radiance Series User Manual - French - 46 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info