Manual Vermont Castings Radiance Series (page 15 of 56) (English)

815507

Zoom out

Zoom in

1/56

1515 3-90-30007498Vermont Castings • Radiance RADVT Installation Manual_R32 • 10/23

Before You Start

Plan your installation. Set the stove in place and survey how

to best vent the unit. Select the appropriate termination kit

and vent pipe for the installation. Read these instructions

and the stove Owner’s Manual before beginning installation.

After vent conguration has been decided, begin attaching

pipe to unit.

Items required for installation:

Tools:

Hammer Saw and/or saber saw

Level Measuring Tape

Electric drill and bits Pliers

Square

Building Supplies:

Framing materials

Wall nishing materials

Caulking Material (noncombustible)

• These models are approved to use HHT direct vent

pipe components, HHT termination kits and DuraVent

components. No other venting system components may

be used.

• Horizontal runs must be supported every 3 feet (914 mm)

using wall straps. Vertical runs must be supported every

8 feet (2.4 m) using wall straps. Slip wall straps loosely

on to pipe. Attach straps to framing members using nails

or screws. Tighten nut/bolt to secure pipe.

• The stove and venting system should be inspected

before initial use and at least annually by a qualied

eld service person. Inspect the external vent cap on a

regular basis to make sure that no debris is interfering

with the airow. Inspect entire venting system to ensure

proper function.

Outside Wall

Finishing Material

(Vinyl Siding, etc.)

Figure 3.1 - Termination cap on wall

General Information

The Radiance is approved for installation only with the vent

components listed under Section A “Venting Requirements

& Options”. Follow the vent component instructions exactly.

For U.S. installations: The venting system must conform with

local codes and/or the current National Fuel Gas Code, ANSI

Z223.1/NFPA 54.

For Canadian installations: The venting system must conform

to the current CSA B149.1 installation code.

Install the starter Pipe

1. Attach the starter to the stove.

2. Place a 3/8” bead of sealant around the inside of the cast

starter collar. Stove cement is provided in the manual

bag for this purpose. Insert the 6-5/8” outer adapter into

the cast outer starting collar and press down rmly.

3. Install the CCSLP Outer Adapter Pipe.

4. Place a 3/8” bead of sealant around the 4” crimped

end of the starter collar on the stove. Stove cement is

provided in the manual bag for this purpose. Attach the

SLP pipe to the adapter, and secure by aligning adapter

and pipe seams, pressing down rmly until pipe stops,

and twisting to lock into place, Figure 3.2.

WARNING

Any horizontal run must have a 1/4” rise for every one (1)

foot of run towards the vent termination. Never allow the

vent pipe to run down. This could cause high temperatures

and may present a re hazard.

WARNING

Termination cap must be positioned so the embossed

arrow is pointed up.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Radiance Series in the language / languages: English as an attachment in your email.

The manual is 6.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Radiance Series

Vermont Castings Radiance Series User Manual - French - 46 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vermont Castings Radiance Series Manual

Product: