Manual Vermont Castings Radiance Series (page 19 of 56) (English)

815507

Zoom out

Zoom in

1/56

1919 3-90-30007498Vermont Castings • Radiance RADVT Installation Manual_R32 • 10/23

NOTE:Supporthorizontalpipesevery5'(152cm)with

metal pipe straps.

Vent Termination Below Grade:

Install Snorkel Kit #SLP-SNORK when it is not possible to

meet the required vent termination clearances of 12" (305

mm) above grade level. The snorkel kit will allow installation

depth of down to 7" (178 mm) below grade level. The seven

inches is measured from the center of the horizontal vent

pipe as it penetrates the wall. If the venting system is

installedbelowgrade,awindowwellmustbeinstalled

with adequate and proper drainage.

NOTE: Be sure to maintain side wall clearances and vent

run restrictions. Refer to Figures 2.3 thru 2.6.

1. Establish the vent hole through the wall.

2. Remove soil to a depth of approximately 16" (406 mm)

below the base of the snorkel. Install a window well (not

supplied). Rell the hole with 12" (305 mm) of coarse

gravel and maintain a clearance of at least 4" (102 mm)

below the snorkel, Figure 3.16.

3. Install the vent system as described in Figures 3.2 thru

3.9.

4. Be sure to make a watertight joint around the vent pipe

joint at the inside and outside wall joints.

5. Apply high temperature sealant around the inner and

outer snorkel collars. Join the pipes and fasten the

snorkel termination to the wall with the screws provided.

6. Level the soil to maintain a 4" clearance below the

snorkel.

7. If the foundation is recessed, use extension brackets

(not supplied) to fasten the lower portion of the snorkel.

Fasten the brackets to the wall rst, and then fasten to the

snorkel with self-tapping #8 x 1/2" sheet metal screws.

Extend the vent pipes out as far as the protruding wall

face, Figure 3.15.

6. Use appropriate length of pipe sections – telescopic or

xed – and install. The sections which go through the

wall are packaged with the starter kit, and can be cut to

suit if necessary.

7. Guide the vent terminations 4" and 6-5/8” collars into

their respective vent pipes. Double check that the vent

pipes overlap the collars by 2" (51 mm). Secure the

termination to the wall with screws provided and caulk

around the wall plate to weatherproof. As an alternative

to screwing the termination directly to the wall, you

may also use expanding plugs or an approved exterior

construction adhesive.

Figure 3.13 - Horizontal Length Requirement

Cutout On Vinyl

Vinyl Siding Wall

Termination Cap

Figure 3.14 - Horizontal Termination Cap on a Vinyl Siding Wall

Figure 3.15 - Use extension brackets to mount snorkel against

recessed wall.

ST219

snorkel detail

12/6/99 djt

Recessed Wall

Sheet Metal

Screws and

Bracket

Wall Screws

and Anchors

Waterproof Seal

Around Pipe

Firestop

Finishing

Collar

7" Pipe

Wall Plate

SLP Cap

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vermont Castings Radiance Series in the language / languages: English as an attachment in your email.

The manual is 6.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vermont Castings Radiance Series

Vermont Castings Radiance Series User Manual - French - 46 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vermont Castings Radiance Series Manual

Product: