22695
66
Zoom out
Zoom in
Previous page
1/72
Next page
CAN bus
In many vehicles, speed, reversing and light information can be read out from the ve
-
hicle’s CAN bus and converted into the appropriate signals for the navigation system
using an adapter.
Universal installation
If none of the above-mentioned options are possible, the wheel speed can be con
-
verted into a digital speedometer signal by means of an MA 3400/00 magnetic field
sensor and magnetisation of a tyre.
Reversing signal (A2):
Connect pin A2 to a suitable reversing signal point (positive lead of reversing lamp).
Operation of the navigation system is possible without a reversing signal. The ab
-
sence of a reversing signal may lead to inaccurate navigation.
12-V ignition positive (A4):
Connect pin A4 to a suitable 12-V circuit via the ignition.
A
This connection should be rated for a current of at least 10 A.
Electronic antenna/ motor antenna (A5), optional:
Connect pin A5 to the supply lead of an electronic antenna or to the control line of
a motor antenna.
A
Do not use this connection to power the antenna motor.
Pilot lighting (A6), optional:
Connect pin A6 to a suitable connector of the low-beam positive lead.
When the low beam is switched on, the pilot lighting at the volume control is illu-
minated, even when the radio is switched off.
12-V permanent positive (A7):
Connect pin A7 to 12-V permanent positive at a suitable point.
Connection overview, ISO chamber B (loudspeakers), Fig. 3:
Pin Connection to loudspeaker
B1 + Rear right (RR+)
B2 – Rear right (RR–)
B3 + Front right (FR+)
B4 – Front right (FR–)
B5 + Front left (FL+)
B6 – Front left (FL–)
B7 + Rear left (RL+)
B8 – Rear left (RL–)
A
Use only loudspeakers with an impedance of 4 Ohms.
A
Do not connect the loudspeakers to earth.
A
Do not connect the booster/ amplifier directly to the loudspeaker outputs.
A
Do not connect loudspeakers via an external fader.
Installation instructions
3
66


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Dayton MS 4400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Dayton MS 4400 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info