22695
65
Zoom out
Zoom in
Previous page
1/72
Next page
Electrical connections
Install all cables with care. For wiring details, refer to the connection diagram on the
back fold-out page and the following table.
Do not cut non-assigned wires. Instead, wind them together and secure to one side.
They may be required for retrofitting additional functions.
Connection overview, ISO chamber A, Fig. 2:
Pin Connection
A1 Input digital speedometer signal / SDVC
A2 Switch input reversing signal (reversing light positive)
A3 No function
A4 + 12 V ignition positive/ Accessory contact (Terminal 15)
A5 Switch output for electronic antenna/ relay motor antenna
A6 Switch input pilot light
A7 + 12 V permanent positive (terminal 30)
A8 Battery negative (terminal 31)
A
Connect electrical signals only to suitable points in the vehicle.
A
If a separate connection is made directly to the battery, protect the positive lead with
a 10-A fuse close to the battery (max. distance of 10 - 15 cm).
Digital speedometer signal (A1):
A digital speedometer is required for correct functioning of the navigation system. An-
alogue speedometer signals are not supported by the system.
Connect pin A1 to the vehicle speedometer signal.
A
Never collect the speedometer signal directly from the ABS control or the CAN bus.
Digital speedometer signal requirements:
Frequency: 0 Hz - 4 kHz square-wave signal (no inductive sensor)
Low - level:<1V
High - level:4V-24V
Notes: Many vehicles are equipped with a digital speedometer signal on one of the ra
-
dio connectors. Notes on vehicle-specific information regarding the speedometer sig
-
nal and the above-mentioned accessories can be obtained from your installation ser
-
vice or from our Customer Help Desk.
Operation of the navigation system is possible without a speedometer signal. Ho
-
wever, in the absence of a speedometer signal the following functional restrictions
may arise:
Inaccurate navigation
Inaccurate or invalid information in trip computer
Limitations with regard to SDVC (speed-dependent volume control)
If your vehicle is not equipped to produce a digital speedometer signal, an optional
speed sensor can be installed. This is available as an accessory from your installation
service.
Mechanical speedometer
A digital speedometer signal can be obtained through the installation of a VDO
X39-397-106-191 speed sensor in the speedometer drive shaft.
Installation instructions
2
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Dayton MS 4400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Dayton MS 4400 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info