Manual Thomson ROC 4505 (page 8 of 102) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

607819

Zoom out

Zoom in

1/102

Note: during the programming of a macro, the time bet-

ween eachstep is limited to a fewseconds.Thisleaves little

time for reading the instructions and then carrying them

out.If the mode indicator light blinks and then goes out,it

isbecausethis timelimithasbeenexceeded,youmuststart

again from step 1.

To record a MACRO:

1. Pressand hold down the SETUP keyuntil the

mode key blinks (TV, VCR,…) and then

remains lit (after 2 or 3 seconds).

2. Release the SETUP key.

3. Press the MACRO key once.The mode key

blinks.

4. Press once the A,B,or C key which you are

going to use to memorise the sequence.

5. Press once on the (TV,VCR,…) mode key of

the first device you wish to control (the first

key must always be a mode key.)

6. Successively press the keys corresponding to

the commands you wish to send to the

device(s) (9 keys maximum, including other

mode keys).The mode key blinks when each

key is pressed.

7. Memorise your key sequences by pressing

the

MACRO key once.The mode key is no

longer lit and your Macro is complete.

Note:a sequence will be automatically memorised after

thetenth key press (counted fromthemodekey)and the

mode key light will go out.

To use a MACRO:

Press the MACRO key once and, within 20

seconds, press the A, B,or C key you used to

memorise the sequence.

Note: when running a Macro (which takes a few

seconds),ensure that the remote control is aimed at the

device being controlled.

Remarks:

•The default time between sending 2 commands when

using a macro is half a second..However,it is possible

that you will need to add longer periods in your

sequenceinordertoallowenoughtimeforcertain devi-

ces to turn themselves on.To lengthen the time period

between 2 commands,press once on the key and

thenpressoneof the keysfrom1to9in ordertoinsert

a pause from 1 to 9 seconds.

•The first key in a sequence must always be a (

TV,

VCR,…) mode key.

Deleting a MACRO:

1. Pressand holddown the SETUP key until the

mode key blinks (TV, VCR,…) and then

remains lit (after 2 or 3 seconds).

2. Release the SETUP key.

3. Press once on the

MACRO.key.The mode

key begins to blink.

4. Press once the A, B,or C key that repre-

sents the sequence to delete.

5. Press and hold down the SETUP key. The

mode key light goes out and the sequence is

now deleted.

Learning function

If the make of the device you wish to control is

notin theseparate code list,you can copy thekey

functions of the original remote control of the

device into your ROC 4505.Depending on the

format of the transmission codes of the original

remote control,your ROC4505remotecontrol can

memorise up to150 keys

Global delete – Delete all the keys

copied (this is recommended the

first time you use this function)

1. Hold down the SETUP key until the key cor-

responding tothe lastselected moderemains

lit.

2. Release the SETUP key.

3. Press twice on the LEARN.key.The key goes

out and then relights.

4. Press once on the SETUP key. The mode key

goes out after several seconds.

5. All the copied keys are now deleted.

Before starting

•The batteries in the 2 remote controls must be in

good condition;change them if necessary.

•The keys L1 to L4 allow you to copy 4 additional

keys.

•First copy 2 or 3 keys from the original remote

control in order to check the compatibility of the

codes of both remote controls.Then carry out a glo-

bal delete of these keys before starting the full

learning procedure.

•Lay out the original remote control and your ROC

4505 end to end so as to align the LED diodes on

the 2 remote controls.Where necessary adjust the

height of both remote controls so that the LED dio-

des are properly aligned.

•Check that the 2 remote controls are approximately

2.5 cm apart (a thumb width).

•Do not move the remote controls during the learning

procedure.

•Ensure that the room is not lit by fluorescents tubes

or low consumption lamps since such light sources

can interfere with the copying.

•The 2 remote controls must be at least one metre

away from any light source.

•Avoid copying

VOL and keys codes and the play

keys (8) since depending on the remote controls the

codes of these keys do not necessarily control the

same devices.

• When the memory of your ROC 4505 is full,the

mode key will blink for 3 seconds.It is then not pos-

sible to copy any more codes without first carrying

out a global delete.

•When you copya key,it is possiblethat the mode key

will blink feebly.In this case,do not release the key

and wait until the blinking stops.

Note 1:if the learning procedure does not seem to work

correctly,try the following:

1. End the learning procedure by pressing SETUP.

2. Check that the LEDs of the two remote controls

are properly aligned. Carry out the alignment

procedure.

3. Modify the distance between the remote

controls,increasing or reducing the distance from

1.5 cm to 5 cm.

4. Restart the procedure from the beginning.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC 4505 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC 4505 Manual

Product: