Manual Thomson ROC 4505 (page 7 of 102) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

607819

Zoom out

Zoom in

1/102

Try outother remote control keys to find outthe

range of functions you can control. If you think

that not all of the keys are active,repeat the pro-

cedure of this programming method to find out

the code supporting a wider range of features.

Method D - Automatic code search

With this method, the remote control scrolls

through the full code list by sending an IR signal

to the set to be controlled remotely. Proceed as

follows:

1. Check that your equipment is on. If not,

switch it on manually.

2. Hold the

SETUP key down until the key cor-

responding to the last selected mode blinks

and then remains lit (the indicator lamp

remains lit for several seconds in order to let

you continue with the following steps. The

blinking of the indicator indicates the end of

the available time,then it goes out).

3. Release the

SETUP key.

4. Press the key corresponding to the type of

equipment (for example

TV).

5. Press the PROG .key once.After a few

seconds the remote control begins to list all

the codes included in the library (around 1

code per second). Press

PROG a second

time to reduce the speed of the test (1 code

every 5 seconds).As soon as the device chan-

ges channel you must immediately press

to record the code and stop the listing.If you

don’t react quickly enough, simply return to

the previous code by pressing

PROG (you

can restart the forward listing by pressing

PROG .As soon as the device reacts again,

press

OK to record the code.

Method E – Programming for

control of a COMBO (combined TV-

VCR, TV/DVD, VCR/DVD, … set)

Depending on the COMBO group (TV/VCR,

VCR/DVD,etc.) and the make,you will be requi-

red to enter a single code for both devices in the

COMBO,or to enter two codes, one code per

device.Consult the separate list to discover this.

Before you start programming,you must find the

subcode or code of the subset to be controlled

(television or video recorder).

Refer to the list supplied with this user manual

(see page subcodes or codes).

1. Switch on the COMBO you want to control.

2. Hold the

SETUP key down until the key cor-

responding to the last selected mode blinks

and then remains lit.

3. Press the key of the first device to control,

and then follow one of the programming

methods A, B,C or D previously described.

4. Ifa second codeprogrammingis required,then

repeat steps 2 and 3 above.

How to retrieve a programmed

code?

It may be useful to retrieve the code program-

med in the remote control.

1. Hold the

SETUP key down until the key cor-

responding to the last selected mode blinks

and then remains lit.

2. Press the key that corresponds to the type of

equipment you want to control:

TV:television set - DVD:DVD player -VCR:video cas-

sette recorder - SAT: satellite / cable - AUDIO: Hifi

system.

3. Press the SETUP key briefly, so that the last

mode selected blinks once.

4. Press the numbered keys in ascending order

(0 to 9) until the selected mode blinks once.

5. The digit that makes the selected mode flash

is the first of the 4 digits in your code.Make

a note of it.

6. Repeat step 4 to find out the other numbers

of the code.

7. Once you have found the fourth digit, the

selected mode indicator goes off.

Check of the programming

•For a television or a satellite receiver:switch on and,

for example,press 2 to change channels.

•Video recorder:load a tape and then press .

•DVD player:load a DVD and then press .

other

mote

contr

out

the

functions you can control.If you think that not all of the

keys are active,try the programming Method B or C.

Whenyou have retrievedthecodeof your set,jot itdown

so that you can use it whenever needed.

Programming a sequence

of commands (Macro)

The MACRO key in coordination with one of the

keys A, B,or C allows the programming and

memorisationof up to 3 command sequences(the

automatic and successive pressing of several keys

of your choice). Thus any sequence of key com-

mands can be reduced to merely 2 commands

(MA

CRO key + A, B,or C key). For example after

programming,by pressing MACRO then keyA you

could turn on your television set,turn on your

satellite or cable receiver,zap to a preferred chan-

nel,turn on your video cassette recorder and start

a recording session (providing a cassette was pre-

viously loaded).You can memorise a sequence of

10 commands with each A, B,or C key.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC 4505 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Thomson ROC 4505 Manual

Product: