607819

Thomson ROC 4505 Manual

6
Zoom out
Zoom in
Previous page
1/102
Next page
Note 2:To control 2 devices of the same type and same
make (2Thomson video cassette recorders, 2 Thomson
satellite receivers, etc.) first make sure that these two
devices have been already adjusted to react to different
subcodes (A and B codes onThomsondevices).Thensuc-
cessively program 2 mode keys using method D.
Programming
the remote control
Method A – Fast programming with
1-digit subcode
Before you start programming,you must find the
subcode of the set to be controlled.
Refer to the list provided with these instructions,
page I of the subcodes.
1. Switch on the set you want to control.
2. Hold the SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit (the indicator lamp
remains lit for several seconds in order to let
you continue with the following steps.The
blinking of the indicator indicates the end of
the available time,then it goes out).
3. Pressthe key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO: Hifi
system.
4. While the indicator is lit,type in the subcode
(example:1 forTHOMSON).
5. Direct the remote control towards the set
andtryto switch itoff by pressingthe key.
6. If the set you want to control switches off,
press OK to memorise the subcode.
7. Should the set not switch off, press key,
repeatedly,until the set switches off.Between
twokeypresses,leaveenoughtime for thekey
corresponding to the selected mode enough
time to light up again (about 1 second).
Proceeding this way will enable you to see
whether the set responds or not.
8. Immediatelyuponthe switching-offof the setto
be controlled,press
OK to store the subcode.
Check of the programming
In principle,your set is ready for receiving the remote
controlcommands.Check your remote control forproper
functioning by performing the test described on page 3.
Method B – 4-digit codes
Programming
Before you start programming,you must find the
code of the set to be controlled.
Refer to the list provided with these instructions,
page II of the codes.
1. Switch on the set you want to control.
2. Hold the SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit (the indicator lamp
remains lit for several seconds in order to let
you continue with the following steps. The
blinking of the indicator indicates the end of
the available time,then it goes out).
3. Pressthe key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO:Hifi
system.
4. While the indicator is lit,enter the first digit
ofthe 4-digit codeproposedfortheset to be
controlled (example:0036 forThomson).
5. Direct the remote control towards the set
andtryto switch itoff by pressingthe key.
6. Should the set not switch off,repeat step 2.
Then type in the next 4-digit code.Try to
switch off the set by pressing key once.
Repeat this procedure by trying out each of
the 4-digit codes.
Check of the programming
In principle,your set is ready for receiving the remote
controlcommands.Check your remote control forproper
functioning by performing the test described on page 3.
Method C – Programming by means
of code retriever
Should none of the codes work,you still have the
possibility of retrieving the appropriate code
without having to perform any input.
1. Switch on the set you want to control.
2. Hold the SETUP key down until the key cor-
responding to the last selected mode blinks
and then remains lit
3. Pressthe key that corresponds to the type of
equipment you want to control:
TV:television set - DVD:DVD player -VCR:video cas-
sette recorder - SAT: satellite / cable - AUDIO:Hifi
system.
4. Direct the remote control towards the set
and try to switch it off by pressing the
key.
5. If the set you want to control switches off,
press
OK to memorise the subcode.
6. Should the set not switch off,press key, as
many times as required (up to 200 times),until
the set switches off.Between two key presses,
leave enough time forthe key corresponding to
theselectedmode enoughtime tolightup again
(about 1 second).Proceeding this way will ena-
bleyoutoseewhetherthe setrespondsornot.
7. Immediatelyupon the switching-off of the set
to be controlled,press
OK to store the code.
Check of the programming
In principle,your set is ready for receiving the remote
controlcommands.Check your remote control forproper
functioning by performing the test described on page 3.
2
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Thomson ROC 4505 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Thomson ROC 4505 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info