Manual Telair TIG3000B Inverter generator (page 16 of 44) (English)

688826

Zoom out

Zoom in

1/44

TIG 3000 B

Vers. 001

(Normally Open) type, emergency stop button.

When the contact is closed (emergency button

pressed), the generator will stop immediately

and power is cut from its electronic circuits.

5.8 Connection to the fuel tank

The generator can be connected to the vehicle’s

fuel tank (provided it uses the same type of fuel).

In this instance the generator must be supplied

by a circuit fitted with independent fuel pick up

and return. It is absolutely imperative that the

generator’s fuel line is not connected to that of

the vehicle’s engine, as this could result in seri-

ous malfunctions and invalidate the warranties of

both.

For the connection to the fuel tank use only fuel

grade tubing of a suitable diameter.

Make sure that the cross-section of the tubes is

not reduced by choking, bending or squashing.

Available options are a fuel tank equipped with a

filler that can be fitted to the side of the vehicle

(code 05466) and another with only a cap (code

05472), both of about 15 litres capacity, which

can be positioned either vertically or horizontally,

fitted with a tap with a reserve indicator.

When choosing the position in which to install the

fuel tank, ensure that the fuel line length is as

short as possible.

Position the fuel tank away from sources of heat

and in a location protected from external water.

The level of the tank must differ by no more than

20 cm from that of the generator. If the fuel tank

is installed at a level that is 0.5 m lower than that

of the generator, it may be necessary to install an

additional fuel pump.

An optional electric pump (code 00507) is avail-

able that can easily handle differences in levels

greater than one metre.

5.9 Connecting two TIG3000B units in

parallel

Should it be necessary to double the available

power, it is possible to connect two TIG3000B

units in parallel (they must have the same or

compatible hardware and software revision lev-

els). The connection must be carried out follow-

ing the wiring diagram at Fig. 25.

1 = TIG 3000B #1

2 = TIG 3000B #2

3 = Battery (may be common)

4 = Data cable for parallel connection

5 = TIG #1 230 V output cable

6 = TIG #2 230 V output cable

7 = Connection point of the two outputs

8 = Load connection

The following rules must be observed when car-

rying out the parallel connection:

- the connections must be made with the genera-

tors switched off

- the maximum distance between the two genera-

tors must not exceed 10 metres

- the length of cables 5 and 6 from the outputs of

the generators to the junction point must be less

than 15 metres each, the lengths must be identi-

cal (a maximum difference of 1 metre is tolerat-

ed) and the wires must be of the same size

- make absolutely certain that the N, L and PE

connections to the user circuit are correct

- the two generators may share the same starter

battery or each may have its own

- with regard to the size of the cables used, com-

ply with the specifications in the paragraph on

electrical connections

If these rules are not complied with the overall

power output will not equate to the sum of the

outputs of the two generators, or worse still,

might create a malfunction with damage to the

generators.

In order for the two generators to be able to work

with the outputs connected in parallel, they need

to exchange data on the synchronisation and op-

eration. This is achieved through the special (op-

tional) data cable code 06688 (Fig. 25 ref. 4).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telair TIG3000B Inverter generator in the language / languages: English as an attachment in your email.

The manual is 12,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Telair TIG3000B Inverter generator

Telair TIG3000B Inverter generator User Manual - Dutch - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telair TIG3000B Inverter generator Manual

Product: