688826

Telair TIG3000B Inverter generator Manual

15
Zoom out
Zoom in
Previous page
1/44
Next page
Vers. 001
TIG 3000 B
15
GB
Identify the route for laying the connection cable
(fig. 21) from the control panel to the generating
set.
Position the connection cable so as to connect
the black connector end (fig. 21 ref. 1) to the con-
trol panel, and the white connector end (fig. 21
ref. 2) to the generating set.
After leading the connection cable out of the hole
in the wall, connect the black connector to the
corresponding connector on the back of the
panel.
Fix the panel (fig. 20 ref. 2) to the wall using the 4
self-tapping screws, then apply the frame (fig. 20
ref. 3) by exerting a slight pressure until you hear
the anchor tabs click in.
The supplied standard cable is 5 m long. Also
available are optional 7 m long, 10 m long and 15
m long cables.
Connect the other end of the connection cable to
the corresponding white connector on the gen-
erator (fig.22 ref. 3).
5.7 Auxiliary connections
The terminal strip (fig.22 ref. 2) and the connec-
tors (fig.22 ref. 4 and ref. 5) allows for the follow-
ing auxiliary (not mandatory) connections:
• AUX PUMP + and - terminals: if necessary
(e.g., long distance to cover between the fuel
tank and generator), it is possible to connect a
12 V direct current electrical auxiliary pump
with maximum absorption of 5 A. (Observe
polarity indications).
• FUEL LEVEL Terminal: 0 Volt active input to
which the pilot terminal of a fuel level reserve
gauge of the on-off type can be connected.
The other gauge terminal must be connected
to the ground (either on the vehicle, or to the
negative pole of the battery connected to the
generator).
• D+ terminal: +12 Volt active input (max 15
volts) with respect to the electrical ground to
which the D+ wire of the vehicle system can
be connected (often marked "Under key
lock"). This wire is live with +12 V voltage
when the vehicle engine is running. The in-
formation is used by the generator to stop at
each change of state of D+.
• REMOTE On-Off connector (fig. 22 ref. 4): this
connector can be used to connect the two
poles of a galvanically isolated open-closed
contact, (for example, the contact of an elec-
tromechanical relay), controlled by a remote
device. When the contact is closed, the gen-
erator will start and it will stop when the con-
tact is opened.
• EPO connector (Fig. 22 ref. 5): this connector
can be used to connect the two galvanically
isolated poles of the contact of a remote NO
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Telair TIG3000B Inverter generator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Telair TIG3000B Inverter generator in the language / languages: English as an attachment in your email.

The manual is 12,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Telair TIG3000B Inverter generator

Telair TIG3000B Inverter generator User Manual - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info