Manual Telair TIG3000B Inverter generator (page 18 of 44) (English)

688826

Zoom out

Zoom in

1/44

TIG 3000 B

Vers. 001

- Before stopping it, disconnect or at least stop

the connected utilities.

- Do not connect power loads exceeding the

maximum power rating; ideally 80% of the

specified rating should not be exceeded so

as to allow for any absorption peaks.

- During the first 50 hours of operation (break-

in) do not to submit the generator to loads

greater than 75% of the rated power

- When the generator is out of use for an ex-

tended period, if it is permanently connected

to a battery, it is recommended that it be run

periodically for half an hour in order to ensure

that the battery remains charged.

- When the generator will not be used again for

a period of time exceeding three weeks, it is

important to remove any extra fuel that could

evaporate and leave sediments inside the

carburettor, which could severely damage

your motor. It is COMPULSORY to complete-

ly drain the carburettor by closing, for exam-

ple, the fuel tap on the tank and running the

generator until the fuel runs out.

7 CONTROL PANEL

The generator is equipped with an original re-

mote control panel from which it is possible to

control its operation (fig.30).

The panel has a access port for connection to an

domotics control unit and a USB port for connec-

tion to a PC.

Controls and signals on the panel (Fig 30):

1 ON/OFF switch: allows control panel activation.

The display 2 and the LED 11 are switched on

2 Display: allows generator operation to be moni-

tored. It shows the operation state and any

messages related to internal diagnostics

3 MENU / BOOST button, dual function key:

pressed normally it allows scrolling the various

menus or confirming the selected options, held

down for at least 3 seconds allows the BOOST

function to be activated or deactivated. This

function must be activated when you are plan-

ning to apply to the generator a single load

with power exceeding 60% of the rated power.

4 Auto button, dual function button: within the

MENUS, it scrolls back through the available

options; with an active panel it allows the

AUTO function to be activated or deactivated.

This function controls the automatic generator

start and stop respectively on reaching the

start threshold and the stop threshold set.

5 Start/Stop button, dual function button: within

the MENUS, it scrolls forward through the

available options; with an active panel it en-

ables the generating set start and stop. Press

it to cancel the AUTO function.

6 LED Booster, it illuminates when the BOOST

function is on (fig.30 ref. 3)

7 MAINTENANCE red LED: the display shows

the type of required maintenance (engine lu-

bricating oil level check or replacement).

8 ALARM red LED: indicates a fault. The display

provides detailed information on the fault de-

tected by the system.

9 GEN ON LED: it illuminates when the genera-

tor is in operation. The display shows the pa-

rameters relating to the state of operation of

the generator.

10 AUTO LED: it indicates that the corresponding

function is active

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Telair TIG3000B Inverter generator in the language / languages: English as an attachment in your email.

The manual is 12,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Telair TIG3000B Inverter generator

Telair TIG3000B Inverter generator User Manual - Dutch - 44 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Telair TIG3000B Inverter generator Manual

Product: