480572
10
Zoom out
Zoom in
Previous page
1/20
Next page
7
PART 2 • English
English
symbol next the channel name. After you have marked all channels for locking, your changes will be saved by pressing
BACK. Now you will have to enter your PIN every time you are switching to a locked channel. If you are not entering the
PIN, the receiver will show after a few seconds the picture of the last watched channel until you enter the correct PIN.
For more information, please refer to “Parental Settings” in chapter 5.4 CONFIGURATION.
Note Above described actions for Move and Delete can only be applied for All Channels” list mode. If you
are in a different channel list mode, a message will be shown to change to this mode or not.
5.2 Favourites
In MAIN MENU screen, use the pq buttons to select Favourites and press OK to enter this menu. In this menu, you
can add channels to the favourite list. With BACK you can always cancel actions and exit the actual menu or submenu.
Select desired channels you want to add to the list. Use the
pq buttons to go through the channel list, furthermore
you can use the RED (PG up) and GREEN (PG down) button to scroll page wise. With OK you switch to the selected
channel. The frequency and the satellite name of the selected channel will be displayed below its picture. With OK you
can mark and unmark channel to FAV group, your changes will be saved as soon you press BACK.
5.3 Installation
In MAIN MENU screen, use the pq buttons to select Installation and press OK to enter this menu. The Installation
Menu consists of following sub-menus: Antenna Installation, First Time Installation, Automatic Search, Manual Search,
Load Settings and Save Settings.
5.3.1 Antenna Installation
In submenu Installation, use the pq buttons to select Antenna Installation and press OK to enter this menu. Here you
can access all important settings concerning your dish installation and you will be able to see signal level (strength)/
signal quality (signal to noise ratio) for selected satellite and transponder. With BACK you can always cancel actions and
exit the actual menu or submenu.
Satellite: Currently approx. 50 preset satellites exist, such as Astra, Hotbird, EuroBird, Turksat etc.
and 4 user defined satellites as User1 - User4. Use the
u button and pq buttons to
select the satellite which is in your area of reception from the list. By pressing OK at the
selected satellite, you can enter a new name for it. Therefore you can use the NUMERIC
buttons.
Dish Type: Use the
tu buttons to change the used dish type. You can choose between DiSEqC 1.0,
DiSEqC 1.2 and GOTO X. If you have chosen the DiSEqC 1.2 or GOTO X you can enter the
according setup menu with OK.
DiSEqC 1.0: Use this setup if you are using dish installation with one or multiple fixed dishes. The
default setup for your country specific satellite is already done (AUT-Astra19.2, GER-
Astra19.2, CZE-Astra23.5, SLO-Astra23.5) on DiSEqC input 1. If your installation contains
another satellite or satellites, please setup corresponding SAT on DiSEqC input 2, 3 and 4.
5.3.1.1 DiSEqC 1.2 Setup Menu
Use this setup if you are using dish installation with motorized antenna. After confirming DiSEqC 1.2 setting with OK
in Dish Type, you will enter the DiSEqC 1.2 Setup Menu. With BACK you can always cancel actions and exit the actual
menu or submenu.
Transponder Settings: If you have chosen a satellite from the installed SAT table, the corresponding reference
transponder is already set. If you want to change the values for reference TP, press OK to
enter its submenu. Use the NUMERIC buttons to enter new values and use
pq buttons
to navigate. Your changes will be saved as soon you press BACK.
Go to Angle: Use the
pq buttons to navigate and NUMERIC buttons to enter a value for the angle you
want to go to. Some DiSEqC 1.2 positioners do not support the “go to angle” command. If
your positioner does not support this function, you can enter 000 for the angle in order to
turn the positioner to the reference zero position.
Motor Speed: Use the
tu buttons to change the speed between fast and slow.
Drive Motor: Use the
tu buttons to drive motor to west or east. To drive the motor towards a specific
direction,
tu buttons should be kept pressed.
Enable/Disable Limits: Use the
tu buttons to enable or disable the software limits for defined east or west limits.
Store Position: If your adjustment has reached the maximum signal strength and quality for the desired
position, you can press OK in order to save this setting.
Set East Limit: If you press OK at the position your motor is currently moved to, it will be saved as east
limit. Now your motor will not move to the east over this set limit.
Set West Limit: If you press OK at the position your motor is currently moved to, it will be saved as west
limit. Now your motor will not move to the west over this set limit.
Recalculate Positions: Use this function to restore possible misaligned dish position. Setup one of the satellite
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7500 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info