480572
11
Zoom out
Zoom in
Previous page
1/20
Next page
8
PART 2 • English
positions and align your dish until signal strength and quality range are satisfying again
and store this position. Now if you setup this specific SAT position correctly, you can apply
realignment on the others by pressing OK at recalculate positions.
Note in order to avoid mechanical damage of your dish, please make sure the east and west limits in your
motor are set correctly and dish would not hit any objects on its movement.
5.3.1.2 GOTO X Setup Menu
This GOTO X function allows you by entering your longitude and latitude to easily drive your motor to the desired
satellite position. Precondition is a motor which supports this function as well. With BACK you can always cancel
actions and exit the actual menu or submenu.
Transponder Settings: If you have chosen a satellite from the installed SAT table, the corresponding reference
transponder is already set. If you want to change the values for reference TP, press OK to enter its submenu. Use the
NUMERIC buttons to enter a new value and use
pq buttons to navigate. Your changes will be saved as soon as you
press BACK.
Longitude: Enter your local longitude with the NUMERIC buttons.
Latitude: Enter your local latitude with the NUMERIC buttons.
Turn to Satellite: Turns your antenna to the selected satellite position.
Turn to Zero: Turns your antenna to the reference (0.0) position.
Note You can set new satellite positions by choosing User Satellites (User 1, 2, 3, 4).
LNB Type, Low Frequency and High Frequency:
These values are automatically setup for UNIVERSAL LNB configuration and cannot be
changed, so other LNB’s as UNIVERSAL cannot be supported!
LNB Power: Here you can enable/disable LNB supply, use the
tu buttons therefore. Adjust this
setting to On, if this receiver is not connected to another receiver via loop-through.
DiSEqC (Off / Tone A / Tone B / DiSEqC 1 / DiSEqC 2 / DiSEqC 3 / DiSEqC 4):
You should set this according to connected switch position of the desired satellite. If your
LNB device is connected directly to your receiver, we recommend to select Off mode. Use
the
u and pq buttons to select and press OK to confirm.
5.3.1.3 Frequency list
Press OK to enter transponder database submenu. This frequency table contains the default transponder database of
selected satellite. Use the
tu buttons to choose desired function. With BACK you can always cancel actions and exit
the actual menu or submenu. The following operations are supported:
Add: You can add new transponders to the list (frequency, polarisation, symbol rate). Press
OK at Add and use the
pq tu buttons for navigation and enter new values with the
NUMERIC buttons.
Delete: Use the
pq buttons to mark the transponder you want to delete. Select Delete with tu
buttons and press OK. Then a message will be displayed. Select YES, if you want to delete
or NO to cancel.
Edit: Use the
pq buttons to mark the transponder you want to edit. Select Edit with tu
buttons and press OK. Now use the
pq tu buttons for navigation and enter new
values with the NUMERIC buttons.
Restore: This function will restore the transponder database to the one which was installed per
default. Highlight Restore with the
tubuttons and press OK to restore the list.
Select Satellite (BLUE): If you press the BLUE button, the satellite list is displayed. Now select a satellite with
pq
which you want to edit transponder data from or perform transponder search.
Start scanning (YELLOW): If you press the YELLOW button, the data of selected transponder will be shown in Manual
Search menu. If all settings are like you prefer, you just need to press OK to start the scan.
The corresponding transponder will be scanned and newly found channels will be added to
the program list. If you want to change the scan method use the
pq for navigation and
tu buttons to change settings.
Search Channels: If you have finally adjusted your dish alignment and satellite setup, press OK to search for
all channels. All parameter values, except satellite name, are dependent on satellite name.
Hence, if you change the satellite, the whole parameters are updated automatically. The
signal indicator in this menu will be updated after a change of satellite parameters.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7500 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info