Manual Spektrum DX8 (page 31 of 42) (English)

708059

Zoom out

Zoom in

1/42



Rotate the roller to highlight Tail Curve then press.



Highlight the desired ﬂight mode at the bottom of the screen then press to select.

Note that the selected ﬂight mode will darken conﬁrming the selection.

N= Normal

1= Stunt 1

2= Stunt 2

H= hold



Move the ﬂight mode switch in the position you wish to adjust the curve to.

Highlight one of the ﬁve available Pitch curve values (Low, 25%, 50%,75%,

High). Press the roller to access that value.

Rotate the roller to adjust the selected point to the desired output position. Note

the position on the graph at the left of the screen.

Repeat this for all desired points.



Rotate the roller to highlight EXPO then press to toggle between INH and ACT.



The DX8 offers eight mixes in helicopter model type. You can program a cyclic-

to-throttle mix to advance the throttle when aileron, elevator and or rudder inputs

are given. This prevents rpm decay during cyclic and rudder inputs. A Swashplate

Mix mixes Aileron to Elevator and Elevator to Aileron to adjust swashplate timing.

Six programmable mixes allow the mixing of any channel to any other channel.

You can assign Mixes to activate in various ﬂight modes as well as with the gear

switch. Programmable mixes include a trim offset function that adjusts the mix

crossover point and a trim include function that applies the master’s trim to the

slave channel.



With the transmitter on and the main or telemetry screen displayed, press the

roller. The Function list displays.

Rotate the roller to highlight Mixing then press. The Cyclic to throttle mix appears

on the screen.



Cyclic-to-throttle mix prevents rpm decay when aileron, elevator and or rudder

inputs are given. This mix advances the throttle position with cyclic or rudder

control to maintain rpm. At full throttle, programming prevents the throttle from

overdriving the servo.

Important: When using a governor, Cyclic to throttle mix is not recommended.



Rotate the roller to highlight the desired box at the bottom of the screen. Press the

roller to darken the box and activate Cyclic Mix in that ﬂight mode position. You

can highlight more than one ﬂight mode position. If all boxes are highlighted, the

C Mix function is always on. If no boxes are highlighted, the function is always off.

N= Normal

1= Stunt 1

2= Stunt 2

H= Hold

M=Mix



Rotate the roller to highlight the desired rate then press. Rotate the roller to adjust

the value. The available positive + and negative - values reverse the direction of

the throttle mix.

Adjust the rates for all desired channels.

To verify that Cyclic mix is working properly and in the correct direction, place the

ﬂight mode switch in one of the active positions. Move the programmed cyclic or

rudder channel noting the throttle position. The throttle position should increase.

If it decreases then the opposite value (positive vs. negative) is needed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX8 in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX8

Spektrum DX8 Quick start guide - English - 100 pages

Spektrum DX8 User Manual - German - 42 pages

Spektrum DX8 User Manual - French - 42 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Spektrum DX8 Manual

Product: