708059

Spektrum DX8 Manual

33
Zoom out
Zoom in
Previous page
1/42
Next page
33

Move the programmed master channel while observing the slave channel. The
slave channel should move accordingly.

The Offset function establishes the point at which the two mix rates converge.
Typically, this rate is center or 0%. If an offset is needed (normally not in a
helicopter), do the following.

Rotate the roller to highlight Offset then press. Rotate the roller to adjust the value.
Positive + and negative - values shift the offset in either direction. Press the roller
to accept.
Trim Include
The trim include function applies trim to the slave channel when the selected
master channel has trim (throttle, aileron, elevator and rudder). Typically this
is used when more than one channel operates a primary control surface (dual
aileron servos, etc.) With trim include activated, the master channel’s trim affects
the slave channel’s trim as well.

Rotate the roller to highlight Trim then press. Press the roller to toggle between
INH and ACT.

Use the Gyro function to program and adjust gyro gain. You can program up to
four gyro gain values to be selected from a variety of switches including the flight
mode switch. You can adjust gyro gain values in .5% increments allowing for
precise gain adjustments. Also, you can program the channel the gyro gain is
controlling. The DX8 displays gyro gain values as N for Normal gain and a T for
tail lock (heading hold). The percentage values are the true gain values in each
mode.

With the transmitter on and the main or telemetry screen displayed, press the
roller. The Function list displays.
Rotate the roller to highlight Gyro then press to access that screen.

The Gyro function defaults to Inhibit. To activate the Gyro function, highlight
Inhibit, then press the roller to access the switch function. Rotate the roller to
access the desired gyro control switch. Press the roller to access the Gyro gain
screen.

You can assign the receiver channel the gyro gain is plugged into in this screen.
The governor and the gyro must use two different channels. A channel used by
the governor function does not appear in the Gyro list.
Highlight Ch: (channel) then press to access the gyro channel function. Select the
desired channel to plug the gyro gain into, normally the Gear channel is used.

Rotate the roller to select the desired gain value then press. Select the gain value.
Any time a T displays, the gyro is in tail lock (Heading Lock). If an N displays, the
gyro is in normal mode.
Repeat this for all desired gain values.
TIMER
The DX8 Timer function allows you to program a Count Down timer or Stop
Watch (count up timer) to display on the main screen. An alarm sounds when
the programmed time is reached. You can program the timer to start using the
trainer switch, the left or right trimmers or automatically when throttle is raised
above a preprogrammed position. Also, an internal timer that shows run time for
a specific model displays on the main screen.

With the transmitter on and the main or telemetry screen displayed, press the
roller. The Function list displays.
Rotate the roller to highlight Timer then press.
EN
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX8 in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX8

Spektrum DX8 Quick start guide - English - 100 pages

Spektrum DX8 User Manual - German - 42 pages

Spektrum DX8 User Manual - French - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info