708059
30
Zoom out
Zoom in
Previous page
1/42
Next page
30


With the Elevator to Flap mix screen displayed, rotate the roller to highlight Ele >
Flp then press the roller. Now rotate the roller to select programmable Mix, 1, 2,
3, 4, 5, or 6 and press the roller. The Mix screen appears.

The Master channel is the controlling channel. The slave is the channel, the
master will be mixed to. The slave channel will follow the master channels input
based on the rate that is programmed.
Rotate the roller to highlight the left INH then press the roller to access the master
channel. Rotate the roller to select the desired master channel. When selected,
press the roller to accept that master channel.
Rotate the roller to highlight the right INH then press the roller to access the slave
channel. Rotate the roller to select the desired slave channel. When selected,
press the roller to accept that slave channel.

Rotate the roller to highlight Sw: at the bottom of the screen. Press the roller to
access the switch select function then select the desired switch to turn on/off the
aileron to rudder mix. If you select On, the mix will always be on.

Rotate the roller to highlight the desired rate then press the roller to highlight that
rate. Rotate the roller to adjust the value. You can reverse the direction of the slave
channel with positive + and negative - values.
Adjust the rate for all both directions/values.
To verify that the programmable mix is working properly and in the correct
direction, place the correlating switch in the active positions, move the
programmed master channel and observe the slave channel. The slave channel
should move accordingly.

The offset function establishes the point at which the two mix rates converge.
Typically this rate is center or 0%. If an offset is needed do the following:

Rotate the roller to highlight Offset then press the roller to highlight the Offset
rate. Rotate the roller to adjust the value. Positive + and negative - values are
available shifting the offset in either direction. Press the roller to accept the offset
value.
Trim Include
The trim include function applies trim to the slave channel when the master
channel you select is a channel that has trim (throttle, aileron, elevator and
rudder). Typically, this is used when more than one channel is used to operate a
primary control surface (dual rudder servos, etc.) With trim include activated, the
master channel’s trim affects the master and slave channels.

Rotate the roller to highlight Trim. Press the roller to toggle between INH and ACT.


The Tail Curve programming functions nearly identically to the Throttle and Pitch
curve programming. You can assign four separate Tail curves or a common Tail
curve to 2 or more flight modes. A graph displays at the left side of the screen to
help you adjust the Tail curves. An Expo function is available that smooths out
the curve.
Note: Only use tail curves when the gyro is in the conventional gain (non-
heading hold) mode.

With the transmitter on and the main or telemetry screen displayed, press the
roller. The Function list displays.
EN
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Spektrum DX8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Spektrum DX8 in the language / languages: English as an attachment in your email.

The manual is 5,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Spektrum DX8

Spektrum DX8 Quick start guide - English - 100 pages

Spektrum DX8 User Manual - German - 42 pages

Spektrum DX8 User Manual - French - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info