617485
9
Zoom out
Zoom in
Previous page
1/46
Next page
7
Optional Sew &
Serge Foot
The Side Cutter is an optional attachment that
will trim the excess material while sewing. This
accessory may be purchased from your
retailer.
Machine Preparation:
Select the Zigzag stitch.
Set width and length according to your sewing
machine manual. After the side cutter is
attached, the stitch width may need to be
adjusted.
Attaching the Cutter
Attach the Cutter, making sure the cutter’s “arm”
fits around the needle bar thumb screw. The
“arm” is the long metal piece on the Cutter, which
moves up and down.
Thigthen the thumbscrew, securing the Cutter.
Slowly turn the hand wheel; the needle should go
over the stitch finger on the Cutter. If the needle
is hitting the metal stitch finger then widen the
stitch width. If the needle is hitting the metal
sides then reduce the stitch width. Never use a
straight stitch.
Sewing Instructions
1. Cut a 1x1-inch notch at top edge of your fabric.
This is necessary because the cutter’s blade
cuts prior to the needle stitching and it is best for
the machine to have material under the needle
while sewing.
2. Place the material OVER the first metal
platform and then UNDER the Second metal
platform. If the Cutter is not cutting, it is usually
due to the material not being placed OVER the
first platform.
3. Sew slowly and gently guide the material. The
Cutter works best if approximately no more than
1 inch is being trimmed away.
Recorta-lados
El recorta-lados es un accesorio que recorta
el excesso de material mientras cose. Los
accesorios adicionales puede adquirir los en
su centro de costura .
Preparación de la máquina
Seleccione la puntada ZigZag.
Seleccione la puntada de acuerdo al manual
de su máquina. Después de que el recorta-
lados esté puesto, el ancho de la puntada
debe ser ajustado.
Colocando el recorta-lados
Coloque el recorta-lados asegurándose de
que el “brazo” esté ajustado alrededor del
tornillo de la barra de las agujas. El “brazo”
es la pieza larga de metal en la cortadora el
cual se mueve de arriba para abajo.
Apriete el tornillo asegurando el cortador.
Despacio voltee la rueda/volante; la aguja
debe ir sobre la uñeta de puntada del
cortador. Si la aguja está pegandole al metal
de la uñeta entonces cambie el ancho la
puntada. Si la aguja está pegandole a los
lados, entonces disminuya el ancho de la
puntada. Nunca use puntada recta.
Instrucciones para coser
1. Corte una muesca de 1x1 de la parte de
arriba de la tela. Esto es necesario porque la
cuchilla del recorta-lados corta antes de que
la aguja cosa y es mejor que la máquina
tenga tela debajo de la aguja mientras cose.
2. Ponga la tela SOBRE la primera plataforma
de metal y luego DEBAJO de la segunda
plataforma. Si el recorta-lados no está
cortando se debe al que la tela no esta puesta
SOBRE la primera plataforma.
3. Cosa despacio y guié la tela suavemente.
El recorta-lados trabaja mejor si sólo se
recorta 1 pulgada a la vez.
82
SAVE THESE INTRUCTIONS
This sewing machine is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the sewing machine by a person
responsible for their safety. Children should be supervised to ensure that
they do not play with the sewing machine.
The noise level under normal operating conditions is less than 75dB(A).
For outside Europe:
The machine must only be used with foot control of Type: GTC-5
220~240V, GTC-5 110~127V manufactured by Dan Yang Guoti Motor &
Appliance Co., Ltd.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Singer P-1250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Singer P-1250 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 9,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info