753050

Sentiotec CK 3 Manual

35
Zoom out
Zoom in
Previous page
1/56
Next page
35
Installation instructions for trained electricians only
5 Variant 1
Install bench sensor FII
Figures 5 7
Install the bench sensor in the sauna cabin about 15
cm below the ceiling and opposite of the heating sys-
tem.
The bench sensor with its overtemperature fuse may
only be connected with the supplied 150° C tempera-
ture-resistant connecting line or an equivalent tempe-
rature-resistant line.
On the outside of the sauna cabin, the temperature-
resistant connecting line can be extended with custo-
mary lines.
WARNING - Electric shock:
Run the power cables separate to other sen-
sor and control lines.
Protect single insulated lines with a pipe
(double insulation).
1. Run line 5 to mounting location of bench sensor
4 in the cabin wall and fix in position with wiring
clips.
2. Separate two half shells 1 of bench sensor 4
and connect two terminals of the up to 150° C
temperature-resistant line according to circuit dia-
gram 7.
3. Insert round adapter plate 2 with the connections
crosswise in half shells 1, close half shells 1
and fix with the two 9 mm long Philips head screws
3.
Check for secure fit of bench sensor 4.
4. Conduct tests according to the chapter “Tests”.
5 Fix bench sensor 4 to the cabin wall opposite of
the heating system with two wood screws 6
keeping a distance of 15 cm to the ceiling.
4 Installing the stove sensor FI
with overtemperature fuse
Figures 4 7
Install the stove sensor with overtemperature fuse in
the sauna cabin about 15 cm below the ceiling and
above the heating system, or in accordance with the
cabin manufacturer's specifications.
Use only the supplied 150° C temperature-resistant
connecting line or an equivalent temperature-resistant
line to connect the stove sensor with overtemperature
fuse.
On the outside of the sauna cabin, the temperature-
resistant connecting line can be extended with conven-
tional lines.
WARNING - Electric shock:
Run the power cables separate to other sen-
sor and control lines.
Protect single insulated lines with a pipe
(double insulation).
1. Run four-pin line 5 to mounting location of sto-
ve sensor 4 in the cabin wall and fix in position
with wiring clips.
2. Separate two half shells 1 of stove sensor 4
and connect four terminals of the temperature-re-
sistant line according to the circuit diagram 7
(observe the color coding on the sensors which
correspond to the figures).
3. Insert round adapter plate 2 with the connections
crosswise in half shells 1, close half shells 1
and fix with the two 9 mm long Philips head screws
3.
Check for secure fit of stove sensor 4.
4. Conduct tests according to the chapter “Tests”.
5. Bolt stove sensor 4 to the cabin wall in alignment
with the heater, keep a distance of 15 cm to the
ceiling, or install in accordance with the cabin
manufacturer's specifications, using two wood
screws 6.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sentiotec CK 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sentiotec CK 3 in the language / languages: English, German as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info