753050
34
Zoom out
Zoom in
Previous page
1/56
Next page
34
3 Installing the control
Continued Figures 2 7
3. Connect sensor lines F I and F II or
FTS II according to circuit diagram 7 to termi-
nal 3 on the right-hand side.
Insert supplied screwdriver A into the rectangular
recess of terminal strip B slightly push down, and
slightly tilt up:
The terminal C underneath opens;
Insert line D, tilt screwdriver down and remove.
Check lines for secure fit.
Connecting the light cables
4. Run the light cables through opening H (connec-
tion range for 230 V / 400 V I) into the base of
the housing 1 and connect according to circuit
diagram 7 to terminal K (as described under
subitems of item 3.).
CAUTION - Damage to the unit
On installation an all-pin shut-off fixture needs to be
provided with a 3 mm contact gap (usually ensured
by the fuse).
Make sure all terminals/pins are assigned correctly.
Connecting supply and heat system lines
5. Run the supply and heat system lines through
openings E, F (connection range for 230 V / 400
V I) into the base of the housing 1 and connect
according to circuit diagram 7 to terminal J
with a max. tightening torque of 1.2 Nm.
NOTE - Further line inputs
Open further line inputs 7, G in the base of the
housing and insert the line grommets depending on the
number of options to be connected.
Installation instructions for trained electricians only
3 Installing the control
Continued Figures 2 7 8
Connecting the steam generator (vapori-
zer)
6. Run the steam generator lines through opening 9
(connection range for 230 V / 400 V I) into the
base of the housing 1 and connect according to
circuit diagram 7 to terminal J with a max. tigh-
tening torque of 1.2 Nm.
Connecting the optional fan
7. Run the fan lines through opening H (connection
range for 230 V / 400 V I) into the base of the
housing 1 and connect according to circuit dia-
gram 7 to terminal K.
Connecting the optional power boost
8. Run the lines to be connected to terminals St1,
St2, St3 of the power boost unit through the ope-
ning G (connection range for 230 V / 400 V I)
into the base of the housing 1 and connect ac-
cording to circuit diagram 8 to terminal K (as
described under subitems of item 3.).
9. Connect all PE conductors to the ground terminals
D.
Fix tight bottom of housing
10. Fasten two, 20 mm long, Philips head screws in
the lower mounting holes 5.
Check secure fit of bottom of housing 1.
11. Fit the housing cover on the base of the housing
1 rotate it downwards and push down until you
hear it lock in position.
Check for secure fit of the control .
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sentiotec CK 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sentiotec CK 3 in the language / languages: English, German as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info