781470
30
Zoom out
Zoom in
Previous page
1/176
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
30 | GB
7. Remaining hazards
The machine has been built using modern technolo-



saw band due to improper handling of the work
piece.

to improper handling, such as working without the
push stick.

wood chips. Wear personal protective cloth such


check saw band for such defects.

saw band. Wear proper gloves.
        
switching on the machine.
The use of incorrect or damaged mains cables can

      




still be present.
-

Proper Use“ and in the entire operating manual.
8. Attachment and operation
Before starting the equipment

a workbench or solid base. There are two holes for
this purpose in the machine foot.




When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
󰀨


-


8.1 Mounting the saw on a work bench (Fig. 3)
A workbench made from solid wood is better than


-
bling the saw on a workbench are not supplied
with the saw. However, use equipment of at least
the following size:
1 
2 Foam rubber base.
3 Work bench
4 Flat seal
5 Washer (7 mm)
6 Hexagonal nut (6 mm)
7 Lock nut (6 mm)
8 Hexagon head screws (6 mm)
First of all, drill holes into the seating surface and
then insert the screws.
A foam rubber base for reduction of noise is not
supplied with the saw either. However, we express-

vibration and noise to a minimum. Ideal size 400
x 240 mm.
8.2 Assembling the work table (Fig. 4 - 6)

table intended for this (7) (Fig. 4). (To replace, dis-
assemble the work table in reverse order.)
Place the band saw blade through the slot on the
machine table. Place the machine table on the ta-

the bracket (c). (Fig. 4.1+4.2)
Screw the machine table tight with the quick re-
lease lever and a washer (E) (Fig. 4+5).
       
does not touch the table.
Fit the bolt M6x40 with two washers and the nut to
the table. (Fig. 5.1)
Using the adjustment screw (F) to adjust the table
to a right-angle. – Use a set square –

quick release lever (E).
Set the scale pointer (G) to 0.
8.3 Fitting the table width enlargement (Fig.
7+7.1+7.2+7.3+7.4)
Remove the two bolts and washers (d) from the
table width enlargement (6). (Fig. 7)
Slide the table width enlargement (6) onto the table
mounted on the machine. Ensure that the clamping
lever (8) is open (Fig. 7.1+7.2).
-


sides. The two bolts are used to limit the extension
of the table width enlargement.
8.4 Fitting the parallel stop (Fig. 8)

-
wards.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HBS261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HBS261 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 9.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info