781470
32
Zoom out
Zoom in
Previous page
1/176
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
32 | GB
The sawblade must not jam!
Storing the push rod (Fig. 17)
In order to have the push rod (R) to hand at all times,
hang it on the device (j) intended for this, at the top

8.10 Transverse cutting gauge (14) (optional)
(Fig. 18)
Slide lateral stop (o) into a groove (k) in the saw
bench.
Release the grip screw (l).
Turn the lateral stop (o) until the desired angular
dimension has been set. The arrow on the lateral
stop indicates the set angle.
Retighten the grip screw (l).
The stop rail (n) can be slid against the lateral
stop (o). To do so, loosen the knurled screws (m)
and slide the stop rail (n) into the desired position.
Tighten the knurled screws (m) again
Attention! Do not slide the stop rail (n) too far in the
direction of the saw blade.
8.11 On/O󰀨 switch (Fig. 1)
To turn the machine on, press the green button „1“
󰀨
󰀨
󰀨
The band saw is equipped with an under voltage
switch. With a power failure, the band saw must
be switched back on again.
Attention!
When working with the machine, all protective devic-

        
       -
󰀨

9. Transport

its frame or the frame plate. Never lift the machine at
-
ing table.
During the transport the saw blade protection must
be in the lowest position and near the table. Never
raise at the table!
Unplug the machine from the mains during transport.
10. Working instructions
The following recommendations are examples of the
safe use of band saws. The following safe working
         
-

dangerous condition and must be interpreted care-

-
ing in closed rooms. A suction device which con-
forms with commercial regulations must be used
for suction in commercial areas.
Loosen the sawband when the machine is not in
-
tice on the tension of the saw band to the machine
for the next user.



Wear suitable gloves when handling sawbands.

mounted on the machine before beginning work.
Never clean the sawband or the sawband guide
with a hand-held brush or scraper while the saw-
band is running. Resin-covered sawbands impair



long hair. Roll up loose sleeves over the elbows.
    
workpiece as possible when working.
 󰀩      
around the machine.


When working on narrow workpieces with manual
feed, use the push stick.
For diagonal cuts, place the saw bench in the ap-
propriate position and guide the workpiece on the
fence.
Insure safe workpiece guidance.
For arced and irregular cuts, push the workpiece
-

area.
Use a pattern for repeated arced or irregular cuts.
Insure that the workpiece does not roll when cut-
ting round pieces.
For safe work when transverse cutting, use the

10.1 Performing longitudinal cuts (Fig. A)
Here, a workpiece is cut in its longitudinal direction.
Position the longitudinal fence (5) on the left side
(if possible) of the saw band, in accordance with
the desired width.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HBS261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HBS261 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 9.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info