Manual Scheppach HBS261 (page 31 of 176) (English, German, Dutch, French, Italian, Polish)

781470

Zoom out

Zoom in

1/176

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 31

• When dismantling, pull the clamping lever (K) up-

wards and remove the parallel stop (5).

• The clamping force of the parallel stop can be ad-

justed at the rear knurled nut (P).

8.5 Adjusting the cutting width (Fig. 8 + 8.1)

• The parallel stop (5) must be used when cutting



• Place the parallel stop (5) on the guide rail (Q) to

the left or right of the sawing blade

• 2 scales (L/M) are printed on the guide rail for the

parallel stop (5), which show the distance between

the stop rail and sawing blade.

• Adjust the parallel stop (5) to the required dimen-

sion in the window (O) and use the clamping lever



8.6 Using the table width enlargement (Fig. 9 - 10)

• 



• Loosen the clamping lever (8) and pull the table width

enlargement out far enough so that the workpiece to

be sawn can lie on it without tipping. (Fig. 10)

8.7 Sawblade changing(Fig. 11 + 12)

• Attention: Pull the mains plug!

• Attention! Wear protective gloves when changing



• Remove the parallel stop and the table width en-

largement in reverse order (Fig. 7-8).

• Open the top and bottom of the housing door.

Open the door locks (2) using a slotted screwdriv-





• Relieve the saw band tension with the clamping

screw (11), remove the band. Fig. 11

• Remove the tape. Remove the saw band from the

saw band rollers and through the slot in the saw

table (7).

• Put on a new saw band. Place the new saw band

in the middle of the two saw band rollers. The teeth

of the saw band must face down towards the saw

table.

Side correction (Fig. 11)

• The sawblade should run in the centre of the band

wheels.

• 



of the handle (J).

• Attention! The saw band should run over the cen-

tre of the band wheel after multiple turns. Visual

inspection!

• -

       

tension screw (11). The degree of tensioning de-

pends on the sawblade width. Wide sawblades

must be tensioned more than narrow ones.

• 



• Attention: Too strong a tensioning will cause pre-

mature breaking.

• Fit the table width enlargement in reverse order.

(Fig. 7-7.4)

• 



8.8 Setting the number of revolutions

(Fig. 12 + 13 + 13.1)

Pull the mains plug!

• Open lower guard. The table top has to be tilted



• Release the belt with the tension handle (12).

• Put the belt into the desired position. (S1 or S2).

• Retension the belt with the tension handle (12).

• 

Rpm range:

Rpm stage 660 m/min.

For processing hardwood, materials similar to



Rpm stage 960 m/min.



8.9 Sawblade guiding (Fig. 14)



button (13).

The upper sawblade guiding can be set from 0 to 175

mm work piece height.

A clearance as small as possible to the work piece

ensures an optimum sawblade guiding and safe

working.

Back pressure bearings (Fig. 15+16)

The back pressure bearings (e) accept the feed pres-

sure of the work piece. Set the upper and lower back

-

es the sawblade back. Tighten the screws (g). The

distance should be 0.5 mm.

Upper guide rollers (Fig. 15)

Set the upper guide rollers (f) to the corresponding

sawblade width. The front edges of the guide roll-

ers must not exceed the tooth base of the sawblade.

 

tighten the screws (g).

Lower guide rollers (Fig. 16)

Set the lower guide rollers (i) to the corresponding

sawblade width. The front edges of the guide roll-

ers must not exceed the tooth base of the sawblade.

 

tighten the screws (h).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HBS261 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 9.05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach HBS261 Manual

Product: