781470
29
Zoom out
Zoom in
Previous page
1/176
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 29

-
ter a power failure.
        
check that the voltage marked on the rating plate


󰀨
Persons working on the machine should not be
distracted.
Note the direction of rotation of the motor and
blade.

put them out of operation.
Never cut workpieces which are too small to hold

Never remove loose splinters, chips or jammed
pieces of wood when the saw blade is running.
It is imperative to observe the accident prevention


-
al associations.
Adjustable protective devices have to be adjusted
as close as possible to the workpiece.
Important! Support long workpieces (e.g. with a
roller table) to prevent them sagging at the end
of a cut.
Make sure the blade guard (3) is in its lower posi-
tion when the saw is being transported.
-
use the machine.

must not be used.
If the table insert is worn, replace it.
Never operate the machine if either the door pro-

are open.
Ensure that the choice of blade and the selected
speed are suitable for the material to be cut.
Do not begin cleaning the blade until it has come
to a complete standstill.
For straight cuts of small workpieces against the
longitudinal limit stop the push stick has to be
used.
The bandsaw blade guard should be in its lowest
position close to the bench during transport.
For miter cuts when the table is tilted, the paral-
lel stop must be positioned on the lower part of
the table.
When cutting round timber, use a suitable holding
device to prevent the workpiece turning.
Never use guards to lift or transport items.
Ensure that the bandsaw blade guards are used


bandsaw blade. Use a push stick for narrow cuts.
The push stick has to be stored on the intended de-
vice, so that it can be reached from normal working

In the normal operating position the operator is in
front of the machine.
When sawing wood, connect the band saw to a
dust collection device.
 
use a suitable holding device that prevents the
workpiece from twisting.
6. Technical data
Electro motor 220 - 240 V ~, 50 Hz
Power 550 W (S2 20 min)
Revolutions 1400 min-1
Saw band length 1790 mm
Saw band width 6 mm
Saw band width max. 13 mm
Saw band speed I 660 m/min
Saw band speed II 960 m/min
 0 - 120 mm
Opening width 245 mm
Table size 300 x 300 mm
Slewing range of the table 0° - 45°
size of workpiece max. 580 x 400 x 120 mm
Weight 24 kg
The work piece must have a minimum height of 3 mm
and a minimum width of 10 mm.

Operation at constant load for 20 minutes or less, fol-
󰀩
duration to re-establish machine temperatures within
2 K of the ambient temperature.
The total noise values determined in accordance
with EN 61029.
sound pressure level LpA 77,4 dB(A)
pA 3 dB
sound power level LWA 90,4 dB(A)
WA 3 dB
Wear hearing protection.
 󰀨     
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HBS261 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HBS261 in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 9.05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info