699578
28
Zoom out
Zoom in
Previous page
1/40
Next page
26 Programming CA-6
Messaging – programming telephone number
FS87 - programming telephone number 1 (HEX)
FS88 - programming telephone number 2 (HEX)
FS89 - programming telephone number 3 (HEX)
FS90 - programming telephone number 4 (HEX)
The functions FS87 to FS90 are used to program the telephone numbers to which the
control panel sends alarm messages. Each telephone number can have up to sixteen
digits and special characters. The numbers are to be programmed in the same way as in
the function FS4.
FS95 - programming assignment of partitions and messages (BIT)
At the moment an alarm occurs, the control panel can send an alarm message to four
telephone numbers. As the system can be divided into independent partitions, the
messaging should depend on which partition is alarming. The FS95 function assigns the
telephone numbers to partitions and defines which message is to be sent.
To program this parameter it is necessary to assign partition and number of message,
which is to be sent to each telephone number. The AB, AB LEDs indicate (in binary
format) the telephone number, which is being programmed.
The LEDs 1 and 2 show the assignment of consecutive numbers to partitions:
1 - telephone number for A partition
2 - telephone number for B partition
A telephone number can be associated with one or two partitions.
The LEDs 5 to 6 show the message, which is sent to a consecutive number:
5 - message 1 to pager
6 - message 2 to pager
Note: If no message for the paging system is assigned to the number, the panel will
send a voice message from the synthesizer.
EXAMPLE:
programming of the following settings (assuming that LEDs 1 to 8 for all numbers are off)
1
st
telephone number - message no. 1 (pager), in case of alarm in A & B partitions,
2
nd
telephone number - message no. 2 (pager), in case of alarm in A partition,
3
rd
& 4
th
tel. number - voice message from synthesizer, in case of alarm in B partition.
[12345] [#] - enter the service mode
[9][5] [#] - call the function (lower B diode is blinking - 1
st
telephone number)
[1] - LED 1 goes on (number 1 assigned to A partition)
[2] - LED 2 goes on (number 1 assigned to B partition)
[5] - LED 5 goes on (message 1 assigned to number 1)
[#] - confirm assignment for number 1 (A LED is blinking - 2
nd
number)
[1] - LED 1 goes on (number 2 assigned to A partition)
[6] - LED 6 goes on (number 2 assigned to B partition)
[#] - confirm assignment for number 2 (A and B LEDs are blinking- 3
rd
number)
[2] - LED 2 goes on (number 3 assigned to B partition)
[#] - confirm assignment for number 3 (upper B LED is blinking - 4
th
number)
[2] - LED 2 goes on (number 4 assigned to B partition)
[#] - confirm assignment for number 4
Messaging – programming of PAGER messages
FS96 - programming message 1 (POLPAGER format)
FS97 - programming message 2 (POLPAGER)
The message is programmed in the same way as in case of direct telephone messaging to
the POLPAGER receiver. The control panel saves in its memory the consecutively
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info