699578
27
Zoom out
Zoom in
Previous page
1/40
Next page
CA-6 SATEL 25
FS85 - programming test transmission time (DEC)
The function sets three time parameters which define the moments of sending the test
transmission code to the monitoring station.
The first parameter (two two-digit numbers: hours, minutes) enables the station to check if
the control panel clock works properly. The mechanism sending the code every day at the
same time can be disabled by programming a wrong time (for example, 99.99).
The second parameter (three two-digit numbers: number of days, hours, minutes) defines
the time counted from the last transmission to the station, after which test code will be sent
by the control panel. After occurrence in the system of any event whose code will be sent,
the panel starts counting the time again. This mechanism can be disabled by programming
00.00.00.
The third parameter (three two-digit numbers: number of days, hours, minutes) makes it
possible to program a separate period of the test transmission, valid only when the system
is armed (for example, when more frequent test transmissions are needed during the
armed mode). The control panel, when system is armed, calls the monitoring station every
period of time specified in the given function. If a new event occurs and the panel sends
its’ code to the monitoring station, then the countdown of the programmed time starts from
the beginning. When 00, 00, 00 value is entered, then, irrespective of whether the control
panel is armed or not, only the time programmed in FS 70 is used.
The programming consists in entering five two-digit numbers. After confirmation of all the
numbers, the panel exits the function.
EXAMPLE: programming the test code to be sent at 1:45 (clock test) and after two hours since the
last transmission (communication test), communication test, when system is armed –
every 15 min.
[12345] [#] - enter the service mode
[8][5] [#] - call the function
[0][1] [#] - enter the hours
[4][5] [#] - enter the minutes of clock test time (sending the message)
[0][0] [#] - enter the number of days,
[0][2] [#] - enter the number of hours,
[0][0] [#] - enter the number of minutes of the communication test time.
[0][0] [#] - enter the number of days
[0][0] [#] - enter the number of hours
[1][5] [#] - enter the number of minutes of the communication test during arm mode and terminate
the function
Note: If the test transmissions are conducted frequently (e.g. every 10 – 15 min.), it is
recommended to activate in function FS5 option number 5 of the first set. Thus
preventing the events memory of the control panel from being quickly filled up, since
only 3 successive events of the test transmission are then saved in memory of the
control panel.
FS86 - programming the „AC loss” report delay (DEC)
The function defines the time from the mains supply loss after which the panel will send an
„AC loss” message to the monitoring station. The delay time is programmed in minutes,
within the range from 01 to 99 minutes. The mains supply loss is signaled instantly in
keypads and on the AC
POWER LOSS
indicator outputs (function 25).
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info