699578
24
Zoom out
Zoom in
Previous page
1/40
Next page
22 Programming CA-6
Note: Assignment of events is necessary for the mode of reporting to both stations with
event assignment. The unassigned events will not be sent, despite the properly
programmed codes.
Monitoring - programming partition event codes
FS69 - programming A partition event codes (HEX)
FS70 - programming B partition event codes (HEX)
The partition event codes can be single- or double-character. For the data formats 4/1 and
3/1, one of the characters must be equal to 0, and the mode of extension by the user
number should be deactivated (see FS47 "Monitoring options ").
When the event codes are to be double-character ones, the panel can extend some codes
with the user number. In case of codes, which are to be extended, one of the characters
should be programmed as 0. Additionally, the mode of extension by the user number
should be activated. The code of event caused by the MASTER user is extended by "F",
the codes of other users – by "1"..."C".
Where the partition is controlled by zones, the event code is extended by "D". When the
event is caused by the clock (see: the "Functions programming TIMERS"), the event code
is extended by "E". Programming the 00 setting means that we cancel sending event
information to the station.
The programming consists in assigning two characters (from 1 to F, 0 means no digit) to
each partition event and confirming them. When programming, the 1 to 8 keypad LEDs
show the programmed code (1 to 4 the first character, 5 to 8 the second character of the
code). The AB, AB LEDs show the number of event programmed, according to the list
below:
Number AB, AB diode state Event
1  Arming *
2  Disarming *
3  Zone bypass *
4  DURESS alarm
5  Silent arming
6  Arming with bypass
7  Partial arming
8  quick arming
9  Clearing alarm
Notes:
The codes, which can be extended by the user number, are marked with *.
The “Silent arming” code is sent in addition to the “Arming” code, which is sent with the
user number.
The “Arming with bypass” code is sent if some of the partition zones are bypassed at
the moment of arming.
The “Partial arming” code is sent in addition to the “Arming” code when in a system
with two partitions one partition is armed and the other is disarmed.
See also: function FS126 (programming the guard control codes).
FS73 - programming A partition event assignment to station 1 (BIT)
FS74 - programming B partition event assignment to station 1 (BIT)
The functions FS73 and FS74 define which events from a given partition will be reported to
the first monitoring station when the mode of reporting to both stations is activated.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info