699578
23
Zoom out
Zoom in
Previous page
1/40
Next page
CA-6 SATEL 21
FS61 - programming zone tamper alarm codes (HEX)
The codes programmed with this function are reported when the CA-6 detects violation of
the tamper contact in 2EOL/NC and 2EOL/NO line, which triggers a tamper alarm.
FS63 - programming zone violation codes (HEX)
The function is used for programming the zone violation codes. The zone violation code is
transmitted to the monitoring station in case of:
violation of an armed delayed zone (of entry/exit, interior delayed, delayed type)
when the control panel has started the entry delay countdown,
violation of an armed counting zone when the number of violations still does not
trigger an alarm,
violation of a day/night zone when it is disarmed,
violation of an armed zone when the zone already signals an alarm - during the
alarm no subsequent alarms are signaled, and the consecutive detector activation is
recorded in the event log as “zone violation”; when the alarm signaling is over, each
next violation of the detector will trigger an alarm.
Note: If the alarms and violation codes are not program for all zones than the station
may not be notified of the alarm. If one of the control panel zones has no alarm
code assigned to it, and it will trigger an alarm, the activation of subsequent
detectors, which occur during the alarm, will be saved in the memory as zone
violation, not as alarm. If the system comprises any zones triggering an alarm of
which the monitoring station is not notified, it is necessary to enter the same
violation codes as for the alarms.
FS64 - programming zone RESTORE (end of violation) codes (HEX)
The codes programmed with this function are sent after the zone returns to its normal state
(according to the setting of corresponding zone options).
FS65 - programming zone TAMPER RESTORE codes (HEX)
The codes programmed with this function are sent after the tamper contact of the detector
connected to the 2EOL/NC and 2EOL/NO zones returns to its normal state.
FS67 - programming zone event assignment to station 1 (BIT)
FS68 - programming zone event assignment to station 2 (BIT)
The functions indicate which zone events are to be sent to station 1, and which to
station 2, if transmission to both stations has been selected in function FS47. The
programming consists in lighting up the LEDs to indicate the events (as per the list below)
and confirming the selection with the [#] key.
No. LED Option
ON
send „zone alarm” code
1
OFF
do not send „zone alarm” code
ON
send „zone tamper alarm" code
2
OFF
do not send „zone tamper alarm" code
ON
send „zone violation” code
4
OFF
do not send „zone violation” code
ON
send „zone restore” code
5
OFF
do not send „zone restore” code
ON
send „zone tamper restore” code
6
OFF
do not send „zone tamper restore” code
The state of LEDs 3, 7 and 8 is irrelevant.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info