699578
22
Zoom out
Zoom in
Previous page
1/40
Next page
20 Programming CA-6
Monitoring - programming identifiers
FS48 - programming event identifier for station 1 (HEX)
FS54 - programming event identifier for station 2 (HEX)
The functions FS48 (station 1) and FS54 (station 2) are used to program the identifiers
transmitted to the monitoring stations. Programming is carried out in the manner typical for
hexadecimal functions (HEX); the LEDs 1 to 8 shows two consecutive characters, which
can be changed by entering new ones. When the first two characters are being
programmed, the lower B LED blinks, and when the other two - the lower A LED.
For the data formats 3/1 and 3/2, the last character should be 0 - the control panel will
send characters from 1 to F, 0 not being sent.
Note: If the monitoring station requires an identifier containing the digit zero, enter the
character “A instead of zero (e.g. the identifier “1203” should be entered as
“12A3”).
EXAMPLE:
programming the identifier for the station 1 = A243
[12345] [#] - enter the service mode
[4][8] [#] - call the function
[
*
0][2] [#] - enter the first two characters of identifier (B LED blinking)
[4][3] [#] - enter the next two characters of identifier (A LED blinking) and confirm them - exit the
function
Monitoring - programming zone event codes
The zone event codes are programmed in the functions FS60, FS61 and from FS63 to
FS65. Each of them is used for programming a code of one event for each of the eight
zones.
The zone event codes may be either single or double character. If a single-character code
is entered (for the data formats 4/1 and 3/1 and also when using the mode with code
extension by zone number, see FS47 "Monitoring options"), one of the characters must
be 0. Programming 00 will result in skipping the event when the events are being
reported to the station.
The programming consists in entering two characters (from 0 to F) for each zone and
confirming them. During the programming, the keypad LEDs show value of the character
entered (from 1 to 4 - the first character, and from 5 to 8 - the second character of the
code) and number of the zone for which the code is programmed (AB, AB LEDs). After the
last zone code is confirmed, the control panel exits the function .
FS60 - programming zone alarm codes (HEX)
The codes programmed with this function are reported when the control panel detects
zone violation, which triggers an alarm.
Codes of 8 control panel zones are programmed in turn.
EXAMPLE:
programming the alarm codes for the zones 1 to 7 (codes from 41 to 47), the zone 8 is
not an alarm one.
[12345] [#] - enter the service mode
[6][0] [#] - call the function
[4][1] [#] - program the code for zone 1
[4][2] [#] - program the code for zone 2
[4][3] [#] - program the code for zone 3
[4][4] [#] - program the code for zone 4
[4][5] [#] - program the code for zone 5
[4][6] [#] - program the code for zone 6
[4][7] [#] - program the code for zone 7
[0][0] [#] - program the code for zone 8 (no event for zone 8), exit the function
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Installation Guide - English - 36 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info