699578
16
Zoom out
Zoom in
Previous page
1/36
Next page
14 SATEL Installer Manual
signals in the TTL (0 V, +5 V) standard, hence, a special cable of SATEL manufacture must
be used to connect the panel and computer RS ports. The cable includes a converter
changing this signal into a standard corresponding to the RS-232 interface in the computer
(-12 V, +12 V). The data can be transmitted through the cable in both directions.
The CA-6 control panel should be installed in an enclosed space with normal humidity of air.
The space should be fitted with an available permanent (not detachable) 230 V power supply
circuit with protective grounding.
The control panel can be mounted in the CA-6 OBU housing (this housing comprises
a transformer designed for operation with the control panel power supply), which permits
installation of a battery with 7 Ah capacity. Before the housing is secured to the base, it is
necessary to mount inside the housing plastic distance plugs, which are intended for
subsequent installation of the mainboard.
In case the plugs tend to slip out, the catches fixing the plug in the housing need to be slightly
bent aside (Figure 3). When inserting the plug, press the central part of the head firmly in so
that it is blocked in the housing hole. It is advisable to make sure that the plug, when
pressed, does not slip out from the opening. During installation of the housing, be careful so
as not to damage the wires which will be passed through the hole in its back panel.
When the housing is secured, you can install the control panel main board and proceed to
making the connections.
IMPORTANT: Do not connect the mains power supply and the battery, until all the remaining
connections are completed.
The control panel is power supplied from 230 V AC mains. Negligence or wrong
connection may result in electric shock and pose a threat to life!
Therefore, be particularly careful when hooking up the control panel. In the
process of installation and connection of the control panel, the cable to be used
for mains supply must not be alive!
Connection of keypad
The keypad should be connected to the system with a four-wire line, using the COM, +KPD,
DATA, CLK terminals on the panel. Where standard wire is used, the cable length can be up
to 200 m. Do not use screened wires.
It is recommended to use an untwisted unshielded cable 8x0,5 mm
2
(do not use twisted pair
cables). With recommended cable, the following distances between keypad and control panel
may be used to ensure appropriate power supply:
Distance Lead No. of cores
to 100 m
Supply and common ground
CLK and DATA signals
2 x 1
2 x 1
from 100 m
to 200 m
Supply and common ground
CLK and DATA signals
2 x 2
2 x 1
The keypads may only be supplied from the +KPD connector of the control panel. This
output can also be used to supply detectors connected to the keypads, if the total current
value of 1.5 A is not exceeded.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-6 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-6

Satel CA-6 Additional guide - English - 40 pages

Satel CA-6 Quick start guide - English - 8 pages

Satel CA-6 Additional guide - German - 19 pages

Satel CA-6 User Manual - German - 19 pages

Satel CA-6 Installation Guide - German - 80 pages

Satel CA-6 User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info