699577
33
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 31
Connection with the station is established in the following way:
the station answers the call and sends the, so-called, handshake signal (one or a few in
sequence if the station supports several transmission formats),
the control panel recognizes the station handshake signal and if it matches the
programmed transmission format, the control panel answers by sending identifier and
event code in appropriate tones (once or twice, depending on the selected format) – in the
headset connected to the line monitoring jack, these sounds are much louder than the
monitoring station signals,
if the station receives information, it will acknowledge it with the same signal as the
handshake,
the panel disconnects or sends next codes if there still are some other events to be
reported to the station.
The most common monitoring problems result from inaccurate information on the
transmission formats supported by the given station (e.g., ambiguous names of the formats),
errors in the data entered into the control panel, as well as poor quality of the telephone
connections. Often only by “monitoring” the course of communication you are able to find the
cause of a problem.
Note: Some stations do not acknowledge reception of the event code if it has another format
(e.g., 4/1 instead of the required 4/2). If this is the case, the control panel will repeat its
attempts to establish communication, while telephones in the facility will be
disconnected the costs of such connections may be very high. For this reason, it is
recommended that all the programmed codes be very carefully checked. It is possible
to activate the options 7 and 8 in FS-47, which makes the panel omit the codes
unacknowledged in 16 consecutive retries. Problems of this type do not occur in
professional, multi-format monitoring stations (including the Satel STAM-1).
Downloading – telephone communication with the computer
Telephone communication with the computer requires a modem. The modem must meet two
essential conditions:
1. enable operation in the transmission format UTI V.21 (CCITT V.21) or BELL 103
(operation at a rate of 300Bps on telephone line),
2. permit operation to be configured only in one of these formats (the function of automatic
format negotiating disabled).
Before starting the first connection between the computer and the control panel, appropriate
settings must be entered in the DLOAD10 program (CONFIGURATION window). Information
on the modem configuration is contained in the DLOAD10 program „HELP” file (function
activated with F1 key), topic: “COMMUNICATION” and in chapter Program configuration for
communication with the panel of this manual. In the case of non-standard modems, you
must refer to the modem manual for the information on configuration procedures.
Modem initialization
The program initializes the modem after the „MODEM” item is selected from the
„COMMUNICATION” menu. In case of any trouble, the program will display one of the two
messages:
MODEM NOT RESPONDING which means a technical problem with communication
with the modem, e.g. an incorrect COM port number, conflict with the Windows system
drivers;
BAD COMMAND – wrong command initializing the modem.
Correct initialization of the modem does not mean it is properly configured to work with the
control panel. The first initializing commands, as suggested in the program, are sufficient
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info