699577
31
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 29
FS87 to FS94 – enter at least one telephone number,
FS95 – define the partitions from which alarms are to be reported to the telephone
numbers programmed in functions FS87–FS90,
FS100 number of telephone messaging queues higher than zero and number of redials
in a queue.
Note: You should also program in FS95 what kind of message will be sent – if no message is
selected for the pager, the control panel will notify with a voice message from the voice
synthesizer.
When the above parameters are correctly programmed and the alarm is triggered, the on-
board LED (designated as „DIALER”) should go on, which indicates that the panel has
started telephone messaging (with pulse dialing the LED is blinking). It is recommended to
test the messaging. To this purpose, use the ordinary headset connected to the „telephone
line monitoring” jack in the SM-2 synthesizer (parallel connection of a telephone set to
„monitor” the communication will interfere with the messaging operation). The telephone
messaging will start immediately after triggering the alarm. Alarm clearing will interrupt the
telephone messaging.
Typical problems with starting the voice messaging:
control panel takes no attempts to call not all of the above mentioned items were
programmed;
control panel goes on line but fails to dial no dial tone or a non-standard dial tone
from the telephone exchange find out the cause of missing signal or deactivate the dial
tone test option in FS5 if the signal is non-standard;
control panel establishes connection, but sends no voice message wrongly
programmed FS95 – messaging to pager selected, but not voice message from the
synthesizer;
control panel establishes connection, sends a message too early or too late the
control panel recognizes answering the call on the basis of sound signals on the telephone
line, with permissible message sending delay up to 4 seconds from lifting the handset if
commutation signals on the telephone line are non-standard or there is strong interference
(clicks, hum), the panel automatic equipment may not function properly then you can
extend the message by activating the “double message” option in FS5 or deactivate the
call answer recognition option;
control panel reports the alarm more times than the preprogrammed number of
queues – the control panel recognizes answering the call on the basis of a callback signal
if the user lifts the handset too quickly (during the first ring), the control panel may
disregard the message and call again.
Reporting to telephone monitoring station
The monitoring station operator should provide the installer with the data necessary for the
monitoring software. These are:
monitoring station telephone numbers;
transmission format or a list of available formats;
alarm system identifier (facility number one or more for detailed reporting from a big
system);
list of event codes.
In order to start monitoring, the following items should be programmed:
FS43 – monitoring station telephone number if there are two numbers or two
stations, the other number should also be programmed in FS44.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info