699577
30
Zoom out
Zoom in
Previous page
1/43
Next page
28 Installer Manual SATEL
If the described procedure is unsuccessful, the option of hardware access to the service
mode must have been disabled in the control panel by software means. If this is the case,
it is necessary to carry out another procedure which would enable the control panel and
restore the default settings:
1. Disconnect in turn the mains supply and the emergency supply.
2. Set a jumper on J19 RESET pins.
3. Connect in turn the emergency supply and the mains supply.
4. Wait about 60 seconds (±5 sec.) and remove the jumper.
5. Enter from keypad the code: [1][2][3][4][5] (the code should be entered within 15 seconds)
and confirm by pressing the [#] or [
*
] key.
Programming the control panel from the computer
Programming the control panel from the computer via the RS-232 port should be initiated by
calling the service mode and the FS112 communication function in the control panel.
Provision is also made for starting communication without calling the function FS112 which
is convenient if the control panel is already installed on the site and there is no keypad in the
vicinity. In order to start communication without the use of keypad do the following:
1. Disconnect in turn the mains supply and the emergency supply.
2. Connect the cable to RS-232 ports in control panel and computer (Fig. 17).
3. Start the DLOAD10 program in the computer.
4. Select in the program the communication port to which the cable is connected.
5. Select in turn the following functions from the program menu: Communication; Local
connection with...; CA10 (RS-232, without the use of keypad).
6. Follow the messages displayed by the program.
ACTIVATING SELECTED FUNCTIONS
Performance of some functions of the control panel requires that a few to more than a dozen
parameters be programmed simultaneously. This section contains detailed information on
how to program such functions as: telephone messaging, monitoring and downloading.
Guard control function
The functioning of the guard control function consists in automatically checking that the,
so-called, guard code is entered on the keypad with a preset frequency. The entry of the
code is saved in the log event, and so is the trouble to enter the code after a preset period of
time, which can be signaled on an output which has the proper function. These events can be
reported to the monitoring station.
To activate the function you must:
program the guard code – in the user function 2 (creating new user) a code with authority
level 5 (instead of the guard code, the user function 7 can also be used activation of the
„switch MONO" output)
set a suitable timer to perform the „partition monitoring” function (FS106)
program the timer control time (functions FS102–FS105, depending on the partition).
Telephone messaging – alarm reporting
The telephone messaging function requires that the following be programmed:
FS5, FS131 activate the “telephone messaging” option, set the “dialing system” option
as required by the telephone exchange,
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info