699577
29
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 27
If the control panel operates with one keypad, having a default address (1001 jumpers on
pins „A” and „D”), then, after the power is switched on, the keypad will report readiness for
work with four short beeps followed by a long one.
Note: The control panel with default settings will not support a keypad connected to the
CLK1 signal if the default address (1001) has been changed in that keypad.
If the control panel is alarming after power-up, clear the alarm by means of the user access
code (default master code for partition 1: [1][2][3][4]) and proceed to programming
parameters in the service mode.
Upon entering the default service code [1][2][3][4][5] and confirming it with the [#] key, the
control panel will enter the service mode. The
[ALARM] and [ARMED] LEDs will be
blinking alternately. Now, you can proceed to programming the control panel.
Note: For the safety reasons it is recommended that the keypad default address be
changed. Having done the changes, you must run the FS124 function.
If the system includes more keypads or where the zone expander is installed, the control
panel will not support any devices connected to the signals CLK2, CLK3, CLK4 until their
addresses have been programmed in the control panel memory.
Hardware access to the service mode
If the panel does not „see” the keypad when the power is on, and does not respond to the
keystrokes (access code entry), or keeps on alarming, it is necessary to carry out the
procedure of hardware access to the service mode. This allow to program of the
keypad/expander addresses before the normal operating mode is restored. In the other case,
the control panel will start alarming right after the power-up because it has detected the
keypad tampering.
To start the service mode by means of jumpers follow the procedure below:
1. Disconnect in turn the mains supply and the emergency supply.
2. Check the keypad address jumpers and tamper contacts for correct settings.
3. Put a jumper on the control panel RESET pins (J19).
4. Connect in turn the emergency supply and the mains supply.
5. After the keypad beep, remove the jumper from the RESET pins (J19). The operation
will activate the service mode in partition 1 keypad. This will be signaled by the
keypads with four short and one long beeps.
6. Call the service function FS124. The function automatically reads the keypad address and
prepares the control panel for work in a new configuration.
Note: If LCD keypads are installed in the alarm system, call the FS-124 service function
in each LCD keypad. When activated from the LCD keypad, this function automatically
performs additional configuring operations and its activation in each LCD keypad is
necessary for proper operation of the system.
7. To make sure that all the settings are in accordance with the default values, you can
perform the service functions FS107, FS108 and FS110.
Having completed the procedure, exit the service mode using the function FS0 and activate
the service mode again this time from the keypad by entering the default access code
[1][2][3][4][5] confirmed with the [#] key.
If the control panel has re-entered the service mode, it means that its functioning is correct
and that you may proceed with further installation of the system (connection of sensors,
sirens, establishing communication with a computer, if required) and programming of all
necessary parameters.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info