699577
28
Zoom out
Zoom in
Previous page
1/43
Next page
26 Installer Manual SATEL
computer notifies the panel with a DTR signal of its readiness to receive data. Lack of this
signal is reported by the panel as a trouble of the RS-232 port.
After starting the DLOAD10 proprietary program (on the included CD), selecting the
appropriate communication port (CONFIGURATION window) and activating the FS112
service function in the control panel, it is possible to program the control panel from the
computer.
Connection of power supply
The control panel is permanently connected to the mains power supply. Hence, before you
start to work on the system cabling, make yourself familiar with the electrical installation in
the facility. In order to power the control panel, select a circuit where voltage is always
present. This circuit should be protected with an appropriate fuse.
Before connecting the control panel to its power supply circuit, you must turn
off voltage in that circuit.
Description of electrical connections to the CA-10 OBU housing:
1. Connect the 230 V alternating voltage leads to the transformer terminals marked
"AC 230 V".
2. Connect the output voltage wires of the transformer secondary winding to the "AC" (~18 V)
terminals on the control panel main board.
3. Connect the wire of the PE electric shock protection circuit to the terminal block situated
next to the transformer and marked with the ground symbol . This circuit should also be
connected to the control panel protective terminal.
Do not connect the "neutral" wire of the 230 V AC mains supply circuit to the
ground terminal. If there no separate electric shock protection circuit in the
facility, this terminal should be left free.
Control panel power-up starting procedure:
1. Connect the emergency power supply wires to the corresponding battery terminals (the
red one to the battery plus, the black one to the minus). The control panel will not start
on connecting the battery alone (without the mains power connected), however, it will
keep on working in case of the 230 V AC voltage trouble, provided it was already started.
2. Switch on the 230 V AC mains supply – the control panel start follows.
Connection of the power supplies in the prescribed order will permit correct functioning of the
power supply unit and the control panel electronic safety devices, thus avoiding damage to
the security system elements caused by possible installation faults.
Note: If it is necessary to completely disconnect the control panel power supply, the 230 V
alternating voltage should be disconnected first, then the battery. Re-connection of the
power supply is to be performed in the above mentioned order (the battery first, then
the 230 V alternating voltage).
As the control panel has no isolating switch to disconnect the mains supply,
it is important that the owner or the user of the security system be informed on
how the system is to be disconnected from the mains (e.g. by indicating the fuse
which protects the control panel supply circuit).
Starting the control panel
When all electrical connections are made and checked for correctness, you can proceed to
starting the system. It is recommended to begin the work with the control panel with no sirens
connected, as the load can exceed capacity of the power supply unit, thus making start of the
control panel impossible. The sirens can be connected after programming parameters of the
realized alarm system is completed.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info